background image

Page 4

For technical questions, please call 1-888-866-5797.

Item 64013

S

AFET

y

Op
ERA

TION

M

AINTENAN

c

E

S

ETU

p

14.  Do not operate Meter if under the 

influence of alcohol or drugs.  Read 
warning labels on prescriptions to 
determine if your judgment or reflexes 
are impaired while taking drugs. If there 
is any doubt, do not operate the Meter.

15.  People with pacemakers should 

consult their physician(s) before 
use.  Electromagnetic fields in close 
proximity to heart pacemaker could 
cause pacemaker interference 
or pacemaker failure.

16.  Do not test voltage on circuits 

higher than 600 volts.

17.  Do not test current on circuits 

higher than 600A.

18.  Dress properly.  Protective, 

electrically nonconductive 
clothes and nonskid footwear are 
recommended when working.

19.  Wear ANSI-approved safety 

goggles during use.

20.  Only use accessories intended 

for use with this Meter.

21.  Avoid damaging Meter. Use only 

as specified in this manual.

22.  Prior to testing resistance, diodes, 

or continuity; disconnect all power 
to the circuit and discharge all 
high-voltage capacitors.

23.  Performance of this Meter may vary 

depending on battery condition.

24.  Use the proper settings, terminals, 

techniques, and range for the 
tests performed.  Start with the 
range stated in the instructions.

25.  Do not apply voltage to the Test 

Leads when the Meter is in the 
Ohms testing setting.  Damage 
can occur to the Meter.

26.  Do not switch between testing modes 

with the Meter connected to a circuit.

27.  Do not use the Meter at a setting 

marked as blank on the scale.

28.  Have the Meter calibrated by a 

qualified technician every year 
to maintain accurate results.

29.  Do not disassemble Meter; take 

it to a qualified technician when 
service or repair is required.

30.  The warnings, cautions, and 

instructions discussed in this 
instruction manual cannot cover all 
possible conditions and situations 
that may occur. It must be understood 
by the operator that common sense 
and caution are factors which cannot 
be built into this product, but must 
be supplied by the operator. 

 SAVE THESE INSTRUcTIONS.

Содержание 64013

















Отзывы: