background image

7

INDICATOR LIGHTS 

The operating condition of the pump is indicated by the green and red indicator 
lights on the pump control panel.

Indicator lights 

________________________________________________________________ 
Indicator lights___________________________________________________                           

    Fault                 Operation                         Description 

    (red)____           (green)___________________________________________

     Off                       Off                 The electricity supply has been switched off.                           
________________________________________________________________ 
     Off                Permanently        The pump is operating.         
                                  on 
________________________________________________________________                           
   Permanently          Off                The pump has stopped because of a fault.    
           on                                        Restarting will be attempted (it may be  
                                                       necessary to restart the pump by resetting 
                                                       the fault indication). 
                                                       Possible causes: 

                                                  * Too high motor temperatures     
                                                  *  Undervoltage 
                                                  *  Overvoltage 
                                                  *  Too many restarts (after faults) 
                                                  *  Overload                                         

________________________________________________________________ 
Permanently      Permanently        The pump is operating, but it has been  
        on                      on                 stopped because of a fault.    
                                                       Reset the fault indication or switch off    
                                                       the electricity supply. 
 ________________________________________________________________                           

      Note: See Setting By Means Of Control Panel on page 10-12, for information  
                on resetting the fault indication and stopping/starting the pump.

Содержание CHIE VARIABLE SPEED BOOSTER PUMP SYSTEM















Отзывы: