background image

10 

M965654 Rev. 2.2 (12/17)

HOT LINE FOR  HELP

For toll-free information and answers to your questions, call:

(844) CRT-TEAM / (844) 278-8326

IN CANADA  1-800-387-0369   (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

IN MEXICO  01-800-839-1200

P ro d u c t   n a m e s   l i s t e d   h e re i n   a re   t r a d e m a r k s   o f   A S   A m e r i c a ,   I n c .   © 2 0 1 7

To learn more about American Standard Selectronic

®

 Products visit our website at:

www.americanstandard-us.com or e-mail us at: [email protected]

Mon. - Fri.  8:00 a.m. to 8:00 p.m. EST  Saturday  10:00 a.m. to 4:00 p.m. EST

TROUBLESHOOTING FLOW CHARTS

UNIT DOES NOT FUNCTION

1

1

2

2

YES

YES

NO

NO

YES

NO

OPEN EXTERNAL SUPPLY STOPS.

CRITICALLY LOW BATTERY.
INSTALL NEW BATTERY.
 

DEAD BATTERY. INSTALL

NEW BATTERY. REPEAT.

NO

CHECK FOR DAMAGE TO SENSOR WIRE INSULATION.
REPLACE SENSOR. 

ARE EXTERNAL SUPPLY
STOPS OPEN? 

REPEATED DOUBLE FLASH
ON SENSOR?

RECONNECT BATTERY TO SENSOR.
DOES SENSOR FLASH FOR 5 SECONDS?

REPLACE SOLENOID

YES

YES

NO

CHECK FOR DAMAGE TO SENSOR WIRE INSULATION.
REPLACE SENSOR. 

RECONNECT BATTERY TO SENSOR.
DOES SENSOR FLASH FOR 5 SECONDS?

NO

FULLY OPEN EXTERNAL SUPPLY STOPS BY 
TURNING COUNTER CLOCKWISE.
 

INSPECT FILTER ASSEMBLY, AERATOR AND 
SOLENOID VALVE.  REMOVE, CLEAN AND INSERT 
BACK TO ORIGINAL POSITION.
 

CHECK FOR BLOCKAGE

ARE EXTERNAL SUPPLY STOPS FULLY 
OPEN?

REPLACE SOLENOID

WATER IS CONTINUOUSLY RUNNING

LOW FLOW ISSUES

Содержание SELECTRONIC 705X.105












Отзывы: