Fig. 2
1.
Determine location of ENCLOSURE
(1)
. It must be
located with-in the 14" (356mm) by 21" (533mm)
shaded area shown in
Figure 2
in order for electrical
connections from the spout assembly to be made.
NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance
between wall supply and ENCLOSURE (1) must be
taken into consideration.
2.
Remove 4 screws from COVER
(2)
and pull off
COVER
(2)
. Hold the ENCLOSURE
(1)
in desired
location and mark the four mounting hole locations as
shown.
Fig. 2.
NOTE: For AC installation see “AC VERSION; Fig. 2.”
Make power supply connection before mounting
ENCLOSURE (1) to wall.
3.
The ENCLOSURE
(1)
works best if secured to a wall
stud or cross brace within the wall, using the SCREWS
(3)
supplied. If the ENCLOSURE
(1)
is to be installed on
a tile or plaster wall the ANCHORS
(4)
and SCREWS
(3)
should be used.
4.
For installations on drywall or tiled walls;
use
ANCHORS
(4)
and SCREWS
(3)
for securing
ENCLOSURE
(1)
to finished wall. Drill four 1/4" dia.
holes a minimum of 1-3/4" deep. Insert the four
ANCHORS
(4)
flush with face of the finished wall.
Align the ENCLOSURE
(1)
and Install the MOUNTING
SCREWS
(3)
. Tighten to secure ENCLOSURE
(1)
to
mounting surface.
1524mm
(60)
14"
(356mm)
3-3/4"
(96mm)
2-3/4"
(71mm)
3"
(76mm)
21"
(mm)
2
4
3
1
1
1
20"
(500mm)
MOUNTING HOLES
SUPPLIES
WASTE
ENCLOSURE
MOUNTING
HOLES
LAVATORY RIM OR
MOUNTING SURFACE
3
NOTE: If using Mixing Valve (optional) See Sheet
#M968808 for installation instructions.
MOUNT ENCLOSURE; Fig. 2
2
1.
Connect SUPPLY NUT
(1)
from spout assembly to
nipple on top of ENCLOSURE
(2)
. Tighten with
adjustable wrench to make a water tight connection.
Fig. 3.
NOTE; If using the optional Mixing Valve See Sheet
#M968808 for installation instructions.
CONNECT SPOUT HOSE TO
ENCLOSURE; Fig. 3
CONNECT WATER SUPPLY TO
ENCLOSURE AND WALL SUPPLY;
Fig. 4
3
Fig. 3
4
1
2
1
3
3
Fig. 4
2
1.
Insert FIBER WASHER
(4)
into SUPPLY NUT
(1)
on
ENCLOSURE
(2)
.
2.
Connect SUPPLY NUT
(1)
on ENCLOSURE
(2)
to
FLEXIBLE SUPPLY HOSE
(3)
. Tighten to make a
water tight connection. Use two wrenches to tighten if
necessary.
Fig. 4.
3.
Connect FLEXIBLE SUPPLY
(3)
directly to wall supply.
Connection on FLEXIBLE SUPPLY
(3)
is 3/8"
compression. Use adjustable wrench to tighten
connection. Do not over tighten.
Fig. 4a.
Note:
FLEXIBLE SUPPLY
(3)
measures 20" from the
bottom of the ENCLOSURE
(1)
base. If additional
supply length is required, installer must purchase parts
separately.
Important:
If FLEXIBLE SUPPLY
(3)
is too long, loop to
avoid kinking.
COLD WATER OR
TEMPERED
WALL SUPPLY
Fig. 4a
4
M 9 6 8 8 0 9
Rev. 1. 7
