background image

45 - EN

Symptom

Cause

Solution

Page

The nozzle spray 

is not warm.

The water temperature is not set to 

an appropriate temperature.

Set the water temperature to an ap-

propriate temperature.

10

The temperature of the water being 

supplied is relativerly cold.

This is not a malfunction.

When water temperature drops, 

such as in winter, spray strength 

may weaken slightly.

-

The spray does 

not reach the cor-

rect position.

When purchasing a replacement model, the position that the spray 

reaches may feel different due to changes in product design.

This is a feature of the product and is not a malfunction.

-

Nozzle spray is 

weak.

The spray strength is low.

Press the [

 + 

] side of the [Spray 

Strength] button.

15

Nozzle is discon-

nected (hanging)

The nozzle shutter has been 

brushed off during cleaning.

Attach the nozzle shutter correctly.

36

The spray may 

be stronger or 

weaker than 

models you have 

used in the past.

When purchasing a replacement model, the spray may feel stronger 

or weaker compared to the product before replacement due to design 

changes.

This is a feature of the product and is not a malfunction.

-

Back Cleansing, Back Cleansing-Mild, and Front Cleansing (Continued)

Troubleshooting

Содержание Advanced Clean 3.0 SpaLet

























































Отзывы: