American Megatrends Megathon Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 55

background image

Chapter 1 Hardware Installation

5

Step 1

Unpack the Motherboard

Step

Action

1

Inspect the cardboard carton for obvious damage. If damaged,
call 770-246-8600. Leave the motherboard in its original packing.

2

Perform all unpacking and installation procedures on a ground-
connected anti-static mat. Wear an anti-static wristband
grounded at the same point as the anti-static mat. Or use a sheet
of conductive aluminum foil grounded through a 1 megohm
resistor instead of the anti-static mat. Similarly, a strip of
conductive aluminum foil wrapped around the wrist and
grounded through a 1 megohm resistor serves the same purpose
as the wristband.

3

Inside the carton, the motherboard is packed in an anti-static bag,
and sandwiched between sheets of sponge. Remove the sponge
and the anti-static bag. Place the motherboard on a grounded
anti-static surface component side up. Save the original packing
material.

4

Inspect the motherboard for damage. Press down on all ICs
mounted in sockets to verify proper seating. Do not apply power
to the motherboard if it has been damaged.

5

If the motherboard is undamaged, it is ready to be installed.

Set Jumpers

Set all jumpers and install the CPU before placing the motherboard in the chassis.
The steps for setting the jumpers and installing the CPU are in the following
pages.

Avoid Static Electricity

Static electricity can damage the motherboard and other computer components.
Keep the motherboard in the anti-static bag until it is to be installed. Wear an
anti-static wrist grounding strap before handling the motherboard. Make sure
you stand on an anti-static mat when handling the motherboard.

Avoid contact with any component or connector on any adapter card, printed
circuit board, or memory module. Handle these components by the mounting
bracket.

«
...
9
10
11
12
13
...
»

Содержание Megathon
























































Отзывы:

Нет отзывов

Похожие инструкции для Megathon

Бренд: Aaeon Страницы: 132

Бренд: Aaeon Страницы: 50

Бренд: Danbit Страницы: 70

Fatal1ty Z170 Gaming K4 Series

Бренд: ASROCK Страницы: 163

Бренд: Gigabyte Страницы: 40

Бренд: Linear Technology Страницы: 16

Бренд: AMPTRON Страницы: 16

Бренд: BESTEK Страницы: 45

Бренд: Raider Outboards Страницы: 73

Бренд: PRIZM Страницы: 9

STEVAL-PLC001V1

Бренд: ST Страницы: 42

DisplayPort VIP Input Board

Бренд: Lattice Страницы: 21

Бренд: Gigabyte Страницы: 72

Бренд: Gigabyte Страницы: 88

Бренд: Raisonance Страницы: 46

Бренд: Outboards Group Страницы: 44

Бренд: TRU Components Страницы: 4

P35 NEO2-FR - Motherboard - ATX

Бренд: MSI Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды