American Megatrends Megathon Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 55

background image

Chapter 1 Hardware Installation

13

Step 5 Connect CPU Fan

J9 (shown below) is a 3-pin berg that connects the fan on the CPU heat sink to
the motherboard power. J9 is located next to the ATX Power Connector.

All AMD Athlon CPUs are shipped with

a heat sink and a CPU fan

. J9 and J11

are keyed in such a way that the CPU connector can be attached only in the
correct manner.

When the system is in sleep mode, the CPU fan stops. When the system returns
to full-on mode, the fan starts again

Step 6 Connect System Case Fan

The system case fan connector is used with the cooling fan in your system case
to lower the temperature in the system. The system case fan connector is located
by the end of the K7 slot for the CPU. The pinout is:

«
...
17
18
19
20
21
...
»

Содержание Megathon
























































Отзывы:

Нет отзывов

Похожие инструкции для Megathon

Бренд: MSI Страницы: 92

Бренд: DFI Страницы: 104

Бренд: Quick Страницы: 24

Бренд: NXP Semiconductors Страницы: 12

Cypress MB39C502-EVBSK-01

Бренд: Infineon Technologies Страницы: 28

Tiger MPX S2466

Бренд: TYAN Страницы: 1

Бренд: ASROCK Страницы: 26

Бренд: Digilent Страницы: 23

Бренд: Texas Instruments Страницы: 20

Бренд: Texas Instruments Страницы: 21

Бренд: Gigabyte Страницы: 34

Бренд: TRIGEM Страницы: 17

Бренд: Aaeon Страницы: 44

Бренд: Fujitsu Страницы: 27

Бренд: Fujitsu Страницы: 34

Бренд: Fujitsu Страницы: 24

Бренд: Fujitsu Страницы: 26

Бренд: Fujitsu Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды