American Megatrends MegaPlex II Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 140

background image

Megaplex Quad Pentium II Xeon PCI ISA System Guide

24

Step 5 Install Motherboard

The motherboard mounting hole pattern is custom made. The chassis
manufacturer should supply standoffs, and screws. The hole pattern on the
chassis should match the pattern on the board.

Step

Action

1

Place the chassis on an anti-static mat. Connect the chassis to
ground to avoid static damage during installation. Connect an
alligator clip with a wire lead to any unpainted part of the
chassis. Ground the other end of the lead at the same point as
the mat and the wristband.

2

Carefully slide the CPU board (Series 769) into the chassis.
The motherboard should rest level with the chassis.

3

Align the mounting holes on the CPU board with the holes on
the chassis. Place the mounting screws in the holes provided
and tighten them.

4

Mount the memory card (if being used) in the memory card
socket.

5

With extreme caution, place the I/O board in the cabinet so
that the connector on the solder side of the board (J999)
mates with the edge connector (J10) on the CPU board. Press
the boards together to make a firm connection.

Warning:

If the boards do not mate properly before they

are pressed together, the connector J999 on the I/O board can
be severely damaged.

6

Repeat step 3 for the I/O board.

Note:

The memory connector (J1) on the CPU board must be occupied. If the

Series 777 memory card is not used, the connector must be terminated by a
Series 778 memory termination card. If the card in J1 is not inserted properly or
is uninstalled, a red LED (J4) lights up as a warning sign, when the board is
powered (see picture on page 4.)

Cont’d

«
...
30
31
32
33
34
...
»

Содержание MegaPlex II













































































































































Отзывы:

Нет отзывов

Похожие инструкции для MegaPlex II

Бренд: Garz Fricke Страницы: 35

Бренд: IEI Technology Страницы: 126

Бренд: IEI Technology Страницы: 147

Бренд: Gan Systems Страницы: 28

JetBox 9310 Series

Бренд: Korenix Страницы: 21

Бренд: Texas Instruments Страницы: 9

Бренд: JETWAY Страницы: 39

Бренд: Linear Technology Страницы: 7

Бренд: Biostar Страницы: 65

Бренд: Analog Devices Страницы: 17

KXTJ3-1057-EVK-001

Бренд: Rohm Страницы: 3

Бренд: J&W Страницы: 39

NOVA-PV-D5251-G4-R11

Бренд: IEI Technology Страницы: 18

Бренд: NavSpark Страницы: 18

Бренд: ARK Страницы: 44

Бренд: Rioworks Страницы: 87

Бренд: Lex Computech Страницы: 96

Бренд: Lex Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды