American Megatrends MegaPlex II Скачать руководство пользователя страница 131

Страница: 131 / 140

Chapter 7 Flashing the LCD ROM

123

Tools

The following tools are required to upgrade the LCD ROM:

•

sorting header (supplied),

•

floppy with LCD ROM upgrade image,

•

null modem cable,

•

PC with an available serial port, and

•

terminal emulation software.

Flashing the LCD ROM

Use the following procedure to flash the LCD ROM.

Step

Action

Turn off the Megaplex machine

Take off the top cover of the Megaplex chassis.

Take off the cable from the 50-pin connector, P2.

Put the "sorting header" on the 5-pin connector, J2.

When you place the sorting header on the connector, the five holes on the
back of the sorting header face the 50-pin connector, P2.

Connect a null modem cable to the serial connector.

Boot the PC in DOS or Windows.

Connect the other end of the null-modem cable to the serial connector of a
PC.

Run your terminal software.

Turn on the Megaplex machine.

Download the firmware image through the terminal software.

Turn off the Megaplex machine.

Disconnect the null-modem cable and the sorting header.

Reconnect the cable to the 50-pin connector, P2.

Turn on the Megaplex. The LCD is ready.

Содержание MegaPlex II













































































































































Результаты поиска

Содержание MegaPlex II

Отзывы:

Похожие инструкции для MegaPlex II

Бренды по названию

Популярные бренды

American Megatrends MegaPlex II, Системное руководство

Результаты поиска

Содержание MegaPlex II

Отзывы:

Похожие инструкции для MegaPlex II

Бренды по названию

Популярные бренды