American Dryer Corp. ADS-464 Скачать руководство пользователя страница 24

Страница: 24 / 81

4. Exhaust Ducting

The dryer’s exhaust air

must be

vented to the outdoors by the shortest route possible with the number of

elbows kept to a minimum. The duct

should be

designed and installed by qualified technicians.

Improperly designed duct work may reduce the airflow through the dryer, causing improper and unsafe
drying conditions. The static pressure of the air in the duct work

must not

exceed 1.25 inches water column

(3.10 millibar). The dryer exhausts 11,600 cfm (328.5 cmm) of air during the drying cycle, 13,000 cfm
(368.2 cmm) during cool down. Ducting

must be

sized for the 13,000 cfm (368.2 cmm) of airflow.

The exhaust vent connection is located on top of the burner and heater section of the dryer. It has a rectangle
cross section and is flanged.

A sheet metal transition piece is supplied to connect a 24-inch diameter exhaust duct to the dryer’s exhaust
vent connection. Care

must be

taken in locating this transition piece so that the tilting tumbler section does

not hit the transition piece.

The duct work connecting the vent to the outdoors

must be

a minimum of 24-inches in diameter for a round

duct or 625 square inches for a rectangular duct (a 22-inch square duct would be sufficient).

MAN2371

Содержание ADS-464


















































































Результаты поиска

Содержание ADS-464

Отзывы:

Похожие инструкции для ADS-464

Бренды по названию

Популярные бренды

American Dryer Corp. ADS-464, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ADS-464

Отзывы:

Похожие инструкции для ADS-464

Бренды по названию

Популярные бренды