background image

 

In accordance to the standard 

EN 50131-2-4 Grade 2 

Enclosure material 

ABS 

Accessories  

Rotary handle (SN-1 version)* 

Dimensions (H x W x D) 

110 x 60 x 46mm 

Resistance to animals  

NO 

 
 

In accordance with the standards: 
 
R&TTE 99/5/CE  
EN 50131-2-4: 2008  
EN 50131-2-4 Grade 2  
EN 50131-2-4 Class 2  
CEI 79-2: II° Level
 

 

 

RoHS 

 

 

 

*

The holder does not comply with the EN 50131-2-4 standard 

 

Additional information 

The  manufacturer  takes  no  responsibility  for  the  defects  that  result  from  the  damaging,  malfunctioning  or 
inability to operate the equipment especially when resulting from failure to comply with the recommendations 
and requirements contained in the manual. 

It  is  necessary  to  periodically  test  the  signaling  device.  The  majority  of  Intrusion  Detection  Systems 

indicates  malfunctioning  of  the  signaling  devices and  informs  the  user  with  an  appropriate  message  on  the 
LCD  keypad  or  LED  light  on  the  LED  display.  In  case  of  such  situation,  the  system  installer  shall  be  
immediately notified. Testing and control  methods of Intrusion Detection Systems are specifically determined 
by the installer. 

The  MOUSE  01  detector  was  made  in  accordance  with  the  requirements  of  the  EEC  and  99/5/CE 

directives. The Declaration of Conformity is available at 

www.pulsar.pl

  

 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание MOUSE 01








Отзывы: