background image

 

 

 

 

The exclusive distributor of AMC products 

 

MOUSE 01 

Dual Element Digital Motion Detector (dual pyro 
e mic anti-masking)

 

 

CODE 

MU01 

 

In accordance with the 

EN 50131-2-4 standard

 

MANUAL  EN

 

 

Edition: 3 from 07.03.2014 

Supersedes: 2 from 24.02.2014

 

 

1. Introduction 

 

     The MOUSE 01 is a dual element digital motion detector with anti-masking function.  

With  its  advanced  signal  processing  algorithms  and  dual  detection  technology  (PIR  and  MW)  it  is 

characterized  by  very  stable  operation  and  low  rate  of  false  alarms.  Advanced  digital  temperature 
compensation enables operation over a wide temperature range.  

The  range  of  the  MOUSE  01  detector  is  up  to  14  meters.  Special  lens  provides  horizontal  coverage 

exceeding  90  degrees  (29  zones  in  5  levels).  The  detector  features  creep  zone  detection.  The  area  of  the 
sensor operation is shown in the Figure 5a and 5b. 

The anti-masking function is based on the microwave sensor. If the microwave sensor detects any object 

in a distance of several centimeters from the detector, it is interpreted as an attempt to block the detector and 
causes the opening of the NC anti-masking relay for about 2 seconds.  
 

2. Installation of the detector 

 

The detector should be mounted by a qualified installer, holding relevant permits and licenses (applicable and 
required for a given country) for Intrusion Detection Systems. 
The latch system used in the enclosure of the detector eliminates the need for screw connections, so that the 
detector installation is simple and does not take much time.  

Follow the basic rules for the installation of Intrusion Detection Systems (pay attention, among others, not 

to 

soil 

or 

damage 

the 

pyroelectric 

element, 

do 

not 

point 

the 

detector 

towards strong light sources).). The optimum mounting height of the MOUSE 01 detector is 2 meters. 

 
 

 
 
 

 

 

 

 

Fig. 1a 

Main view

 

Fig. 2 b 

Inside view

 

 

 
 
 
 

Содержание MOUSE 01








Отзывы: