Ambirad VISION VT Series Скачать руководство пользователя страница 23

Страница: 23 / 32

Doc No. 700025 Page 23 of 32

3. Commissioning Instructions.

These appliances should be commissioned by a qualified engineer.

3.1 Tools

Required.

The following tools & equipment are advisable

to complete the tasks laid out in this manual.

Suitable alternative tools may be used.

Small Flat
Head
Screwdriver

Manometer

Pozidrive
Screwdriver

Leather
Faced
Gloves

4mm
Allen
Key

10/12mm
Spanners

Large Adjustable
Spanners or 22, 26 &
27mm Spanners for
fitting Of Gas Flex.

13mm
Socket

Wrench with
Extension

Check installation has

been carried out to these

instructions.

YES

Ensure gas and electricity

supplies are isolated.

Disconnect gas hose from

burner

Remove burner from tube and inspect burner head.

(See servicing instructions)

Replace burner on tube

and secure.

Open control housing and

check that all components

are securely fastened.

Reconnect gas hose.

Open isolating valve.

Check soundness.

A successful ignition is indicated by

the amber Lo and Hi fire lights

illuminating and remaining

illuminated.

The heater should now

run through its start up

sequence and ignite.

Turn off power and check

that all components are

securely fastened.

Has the

burner lit?

Check operation on flame failure.

Check gas pressure.

Check

gas pressure

Hi and Lo fire.

Check operation of air

pressure switch.

Check thermostat is set to

call for maximum heat.

Switch on electrical supply.

The red neon should now

be illuminated. If restarting

heater a delay of 15s

should be allowed.

Leave the instructions

with a responsible

person.

Close control housing

Gas Valve adjustment

Injector pressure
test point.

Gas inlet test point

Low set point
regulator

High set point

regulator

(10mm spanner

required)

Содержание VISION VT Series

































Результаты поиска

Содержание VISION VT Series

Отзывы:

Похожие инструкции для VISION VT Series

Бренды по названию

Популярные бренды

Ambirad VISION VT Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VISION VT Series

Отзывы:

Похожие инструкции для VISION VT Series

Бренды по названию

Популярные бренды