Ambirad VISION VT Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 32

Ambirad VISION VT Series Скачать руководство пользователя страница 17

Doc No. 700025 Page 17 of 32

2. Assembly Instructions.

2.2.3 Brackets

There can be two types of brackets supplied
with these heaters:



Type ‘A’ are suspending brackets with
reflector fixing points.



Type ‘B’ are suspending brackets with no
fixing points.



Type ‘C’ is a centre bracket to retain the
reflector. (UT model only)

Slide the bracket assemblies along to the tubes
to the marked positions in their correct order as
detailed in the assembly drawings.

Tighten clamping ‘U’ bolt arrangement to tubes

ONLY WHERE STATED

on the assembly

drawings.

2.2 Assembly

Notes.

2.2.1 Tubes

Identify and position tubes on trestles. For
aesthetics it is advisable to position the tube
seam and coupling fastener so that these
cannot be seen from beneath the heater. Mark
out the position of the bracket centres from the
dimensions shown on the assembly drawings.

2.2.2 Turbulators

Insert turbulators into the tubes ensuring the
correct length and quantity are inserted into
their respective correctly identified tube as
detailed in the assembly drawings.

PLEASE READ

this section prior to

assembly to familiarise yourself with the

components and tools you require at the
various stages of assembly. Carefully open the
packaging and check the contents against the
parts and check list.

The manufacturer reserves the right to alter
specifications without prior notice.

Please ensure that all packaging is

disposed of in a safe environmentally

friendly way.

For your own safety we recommend the
use of safety boots and leather faced

gloves when handling sharp or heavy items. The
use of

protective

eye

wear

is

also

recommended.

Pozidrive
Screwdriver

Trestles

Leather
Faced
Gloves

4 & 5mm
Allen
Keys

Tape
Measure

13mm
Socket

Wrench With
Extension

10mm,

12mm &
13mm
Spanners

2.1 Tools

Required.

The following tools and equipment are advisable
to complete the tasks laid out in this manual.

Please read

these assembly notes in

conjunction with the correct assembly
drawings (figs 9 to 11).

Suitable alternative tools may be used.

«
...
15
16
17
18
19
...
»

Содержание VISION VT Series

































Отзывы:

Нет отзывов