Amazone AMAPAD Скачать руководство пользователя страница 224

Страница: 224 / 237

Troubleshooting

Error codes

Error code

Error

Measure

U1052

Wrong firmware for the steering sub

system.

Update the firmware; see page 52.

U1054

Steering sub system in error mode.

Switch the steering controller off and

back on again.

U1055

The steering controller requires a

reset.

Switch off the steering controller and

the vehicle. Wait for 20 seconds.

Switch the steering controller and

the vehicle back on.

U1056

The steering controller is incorrectly

configured.

Recalibrate the wheel angle sensor;

see page 168

U1061

Parameter settings for the vehicle not

found in the steering sub system.

Select the correct vehicle again; see

page 75

U106 2

The alignment angle must be

calibrated.

Calibrate the alignment angle; see

page 168

U1065

The steering angle sensor must be

calibrated.

Check the vehicle geometry;

recalibrate the wheel angle sensor;

see page 168.

U106 6

The compass must be calibrated.

Calibrate the compass; see

page 167

U1067

New vehicle or new steering controller

detected.

Recalibrate the compass; see

page 167.

U1068

The vehicle profile does not match

with the settings of the steering sub

system.

Check whether the steering sub

system is switched on.

Select the vehicle again; see

page 75.

Select the steering controller again;

see page 78.

U1069

The steering angle sensor of the

steering sub system is not configured.

Contact the dealer.

013418

013419

T | Troubleshooting|

MG5574-

-II | B.1 | 25.10.2016

222

Содержание AMAPAD














































































































































































































































Результаты поиска

Содержание AMAPAD

Отзывы:

Бренды по названию

Популярные бренды

Amazone AMAPAD, Руководство по эксплуатации

Результаты поиска

Содержание AMAPAD

Отзывы:

Бренды по названию

Популярные бренды