background image

SAFETY DIRECTIONS 

Basic Directions

 

This control has been built in accordance with 

EN 12453 Industrial, commercial and 

garage doors and gates - Safety in use of power operated doors - Requirements and EN 
12978 Industrial, commercial and garage doors and gates - Safety devices for power 
operated doors - Requirements and Test methods; 

and left the factory in perfect condition from 

the point of view of safety. To maintain this condition and to ensure safe operation, the user must 
observe all the directions and warnings contained in these operating instructions. 
In principle, only trained electrical technician should work on electrical equipment. They must assess the 
work which has been assigned to them, identify potential danger sources and take suitable safety 
precautions. 

Reconstruction of or changes to CP 970 or the SE 14.21 operator are only permissible with the 

approval of the manufacturer. Original replacement parts and accessories authorized by the 
manufacturer guarantee safety. Liability ceases to apply if other parts are used.  The operational 
safety of the unit is only guaranteed if it is used in accordance with the regulations. The limiting 
values stated in the technical data should not be exceeded under any circumstances (see 
corresponding sections of the operating instructions). 

Specified normal use 

The drive unit is intended for counter-balancing sectional doors.  The safe operation is only 

guaranteed with normal specified use. The drive unit is to be protected from rain, moisture and 
aggressive ambient conditions. No liability for damage caused by other applications or non-
observance of the information in the manual. 

Spare parts 

Use only original spare parts. 

  Symbols 

Warning - This warns that the SE14.21 or other materials may be damaged if 
the appropriate precautions are not taken.   

Danger - This indicates danger to the life and health of the user if the 
appropriate precautions are not taken.  
Note - Important information! 

Содержание SE14.21 CP 970



















Отзывы: