background image

BAGAB00002_Z002

1.

 

MECHANICAL INSTALLATION OF SE14.21 OPERATOR & PANEL 

A.

 

Prerequisites 

The permissible loads on walls, fastenings, mountings and transmission elements must not be 
exceeded.  For maximum holding torques or locking torques refer to technical data. 

Fasteners: 

Self-locking fasteners with a 
minimum strength of 800 N/mm

2

 

(8.8) must be used. 

Utilize the hole diameter to the 

fullest. 

Use adequately dimensioned 

washers for elongated holes.  

     

B.  Mounting the Operator 

The descriptions below apply to general door specifications. The specifications of the door 
manufacturer must also be observed during installation. 

Warning

  

  During installation, be sure to use a lifting device that has a sufficient   load-

carrying capacity 

1. 

Thoroughly grease the door 
shaft 

    

2. 

Mount the Key (not supplied) 

  

3. 

Slide drive unit onto 

1” shaft 

BAGAE01003_Z 002

4. 

Install bolts (M8) with lock 
washer And tighten to 25Nm.  

5. 

Secure bracket to wall or 
support. Bracket fasteners 
are NOT provided. 

6. 

Mount control panel.  Mounting 
fasteners are NOT provided. 

BAGAE01006_Z 001

8 .8

8 .8

8.8

8.8

8 .8

8 .8

25 Nm

BAGAB00003_Z002

3 : 1

BAGAE01001_Z 002

Содержание SE14.21 CP 970



















Отзывы: