16
How to set:
Press the
TIMER 0.5-24 hr
pad on the unit or the
TIMER
pad
on the remote control. Each touch of the
INCREASE
/ DECREASE
pads on the unit or the
INCREASE (+) /
DECREASE (-)
pads on the remote control will set the
timer in 0.5 (1/2 hr.) or 1-hour intervals. (The delay timer
can be set in 0.5 (1/2 hr.) increments if programmed for
under 10 hours, but if the delay timer is set for above 10
hours, the timer will be set in 1-hour increments.) The
SET
light will turn on while setting.
To review the remaining time ,
press the
TIMER 0.5-24 hr
pad on the unit or the TIMER pad
on the remote control. Use the
INCREASE
/ DE-
CREASE
pads on the unit or the
INCREASE (+) /
DECREASE (-)
pads on the remote control to set a new
time if desired.
To cancel the timer, press and hold the
TIMER
0.5
-24 hr
pad until the light on the
TIMER
0.5
-24 hr pad goes off.
u
Swing Pad
Turn on to provide continuous side-to-side air circulation.
For fixed side-to-side air direction, turn on until the de-
sired air direction is obtained, then turn it off.
Remote Control:
•
To ensure proper operation, aim the remote control at
the signal receiver on the air conditioner.
•
The remote control signal has a range of up to 20 feet.
•
Make sure nothing is between the air conditioner and
the remote control that could block the signal.
•
Make sure your batteries are fresh and installed cor-
rectly as indicated on the remote control.
Cool Mode
Use the
COOL
mode at
LOW, MED, HIGH,
or
AUTO
FAN SPEED
for cooling. Use the
TEMPERATURE IN-
CREASE
/ DECREASE
pads to set the desired
temperature between 61° and 86°F in 1° increments.
The compressor will cycle on and off to keep the room at
the set level of comfort. Set the thermostat at a lower
number and the indoor air will become cooler. Set the
thermostat at a higher number and the indoor air will be-
come warmer.
NOTE:
If the air conditioner is off and then turned on
while set to a
COOL
setting, or if it is turned from a fan
setting to a
COOL
setting, it may take approximately 3
minutes for the compressor to start and cooling to begin.
Cooling Descriptions
For Normal Cooling -
Select the
COOL
mode and
HIGH
or
MED
fan with a middle set temperature.
For Maximum Cooling -
Select the
COOL
mode and
HIGH
fan with a lower set temperature.
For Quieter & Nighttime Cooling -
Select the
COOL
mode and
LOW
fan with a middle set temperature.
Energy Saver Mode
Controls the fan.
ON -
The fan will cycle on and off with the compressor.
This results in wider variations of room temperature
and humidity and is normally used when the room is
unoccupied.
NOTE:
The fan may continue to run for a short time after
the compressor cycles off.
OFF -
The fan runs all the time, while the compressor
cycles on and off.
Fan Only Mode
Use the
FAN ONLY
mode at
LOW, MED
or
HIGH
fan
speed to provide air circulation and filtering without cool-
ing. Since the fan only settings do not provide cooling, a
SET
temperature cannot be entered. The room tempera-
ture will appear in the display.
NOTE:
Auto Fan Speed cannot be used when in the
FAN
ONLY
mode.
Heat Mode (on some models)
Use the
HEAT
mode at
LOW, MED, HIGH
or
AUTO FAN
SPEED
for heating. Use the
TEMPERATURE INCREASE
/ DECREASE
pads to set the desired tempera-
ture between 61°F and 86°F in 1°F increments.
Auto Fan Speed
Set to
AUTO
fan speed for the fan speed to automati-
cally set to the speed needed to provide optimum com-
fort settings with the set temperature. If the room needs
more cooling, the fan speed will automatically increase.
If the room needs less cooling, the fan speed will auto-
matically decrease.
NOTE:
Auto Fan Speed cannot be used when in the
FAN
ONLY
mode.
Power Outage Recovery Feature
In the case of a power outage or interruption, the unit will
automatically re-start in the settings last used, after the
power is restored. If the
TIMER 0.5-24 hr
feature was set,
it will resume countdown. You may need to set a new
time if desired.
