Amana C9C96 Series, Руководство пользователя

Страница: 12 / 52

12
High altitude installations may require both a pressure switch
and an orifice/spring change. These changes are necessary
to compensate for the natural reduction in the density of
both the gas fuel and the combustion air at higher altitude.
For furnaces being converted to LP gas, it is strongly rec -
ommended that a LPLP03 kit also be installed. The use of
this kit will prevent the furnace from firing when the LP gas
supply pressure is too low to support proper combustion.
Installation of this furnace at altitudes above 7000 ft (2134 m)
shall be made in accordance with the Listed High Altitude
Conversion Kit available with this furnace.”
L'installation de ce générateur de chaleur à des altitudes
supérieures à 7000 pi (2134 m) doit être effectuée
conformément aux instructions accompagnant la trousse de
conversion pour haute altitude fournie avec cet appareil.
For installations above 7000 feet, please refer to the furnace
Specification Sheets for required kit(s).
Contact the distributor for a tabular listing of appropriate
manufacturer’s kits for propane gas and/or high altitude
installations. The indicated kits must be used to insure safe
and proper furnace operation. All conversions must be per -
formed by a qualified installer, or service agency.
HIGH STAGE LOW STAGE
#45 (1)
#50 (2)
LPM-08* (1) 1.25MM (1)
LPM-30* (2) #57 (2)
PRESSURE
SWITCH
(1) FOR USE WITH ALL MODELS EXCEPT *M9C960303AN
ALTITUDE KIT ORIFICE
MANIFOLD PRESSURE
3.5" w.c. 1.9" w.c.
*supports both Honeywell and White-Rodgers 2-stage valves
0 - 7000
PROPANE
NATURAL NONE
GAS
10.0" w.c. 6.0" w.c.
NONE
NONE
(2) FOR USE WITH ONLY *M9C960303AN
Vent Pipe & Combustion Air
F
AILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN BODILY
INJURY OR DEATH
. C
AREFULLY READ AND FOLLOW ALL INSTRUCTIONS
GIVEN IN THIS SECTION
.
WARNING
U
PON COMPLETION OF THE FURNACE INSTALLATION
,
CAREFULLY
INSPECT THE ENTIRE FLUE SYSTEM BOTH INSIDE AND OUTSIDE OF THE
FURNACE TO ASSURE IT IS PROPERLY SEALED
. L
EAKS IN THE FLUE
SYSTEM CAN RESULT IN SERIOUS PERSONAL INJURY OR DEATH DUE TO
EXPOSURE TO FLUE PRODUCTS
,
INCLUDING CARBON MONOXIDE
.
WARNING
This manual will refer to the pipe that discharges products of
combustion to the outdoors as the “vent” pipe or “flue” pipe.
The pipe that supplies air for combustion to the furnace will
be referred to as the “intake” pipe or “combustion air” pipe.
This furnace is dual certified and may be installed as a non-
direct vent (single pipe) or direct vent (dual pipe) appliance.
M aterials - Installations in the U.S. A
PVC, CPVC, or ABS pipe & fittings are typically used as
venting and intake pipe materials. All 90° elbows must be
medium or long radius types. A medium radius elbow should
measure ~3-1/16” minimum from the plane of one opening
to the center line of the other opening for 2” diameter pipe,
and ~4-9/16” minimum for 3” pipe.
In addition to these materials, Innoflue® by Centrotherm
Eco Systems and PolyPro® by M&G Duravent are also
approved vent and combustion air materials for installations
in the U.S.A. Manufacturers Installation instructions for these
products must be followed. These products have specific
instructions for installing, joining and terminating. Do not mix
materials or components of one manufacturer with materials
or components of another manufacturer. Refer to the following
chart for plastic pipe & fittings specifications
M aterials - Installations in Canada
All installations in Canada must conform to the requirements
of CAN/CSA B149.1-15 code. All vent components, including
primer and cement, must be listed to ULC S636. The certified
pipe and fittings should be clearly marked with the ULC
standard “S636”. The primer and cement used must be of
the same manufacturer as the vent system. For Royal Pipe
System 636; use GVS-65 Primer (Purple) and GVS-65 PVC
Solvent Cement. For IPEX System 636, use PVC/CPVC
Primer, Purple or clear. Use PVC Solvent cement (Gray). For
Canadian installations, ABS may be used as a combustion air
pipe only. ABS is not an approved vent material in Canada.
If ABS is used as a combustion air pipe, it must be CSA
certified. Always follow the manufacturer’s instructions in the
use of primer and cement. Do not use primer and cement
around potential sources of ignition. Do not use primer or
cement beyond its expiration date.
Materials and Joining Methods
T
O AVOID BODILY INJURY
,
FIRE OR EXPLOSION
,
SOLVENT CEMENTS
MUST BE KEPT AWAY FROM ALL IGNITION SOURCES
(
I
.
E
.,
SPARKS
,
OPEN
FLAMES
,
AND EXCESSIVE HEAT
)
AS THEY ARE COMBUSTIBLE LIQUIDS
.
A
VOID BREATHING CEMENT VAPORS OR CONTACT WITH SKIN AND
/
OR
EYES
.
WARNING