background image

7

• 

Set the furnace on a level floor to enable proper 

condensate drainage. If the floor becomes wet or 

damp at times, place the furnace above the floor on 

a concrete base sized approximately 1-1/2” larger 

than the base of the furnace.  Refer to the 

Horizontal 

Applications and Considerations

 for leveling of 

horizontal furnaces.

• 

Ensure upflow or horizontal furnaces are not installed 

directly  on  carpeting,  or  any  other  combustible 

material. The only combustible material allowed is 

wood.

• 

Exposure to contaminated combustion air will result 

in safety and performance-related problems.  Do 

not install the furnace where the combustion air is 

exposed to the following substances:  

 

 

permanent wave solutions

 

carbon tetrachloride

 

deicing salts or chemicals

 

cleaning solutions (such as perchloroethylene) 

 

paint removers

 

cements and glues 

 

 

chlorinated waxes or cleaners

 

water softening chemicals

 

halogen type refrigerants   

 

chlorine-based swimming pool  chemicals

printing inks

varnishes 

hydrochloric acid

antistatic fabric softeners for clothes dryers

• 

Seal off a 

non-direct vent

  furnace  if  it  is  installed 

near  an  area  frequently  contaminated  by  any  of 

the above substances. This protects the 

non-direct 

vent

 furnace from airborne contaminants. To ensure 

that the enclosed 

non-direct

 

vent

 furnace has an 

adequate  supply  of  combustion  air,  vent  from  a 

nearby  uncontaminated  room  or  from  outdoors.   

Refer to the 

Combustion and Ventilation Air 

Requirements

 for details.

• 

If the furnace is used in connection with a cooling 

coil unit, install the furnace upstream or in parallel 

with the cooling coil unit.  Premature heat exchanger 

failure will result if the cooling unit is placed ahead 

of the furnace.

 

For vertical (upflow or downflow) applications, the 

minimum cooling coil width shall not be less than 

furnace width minus 1”.  Additionally, a coil installed 

above  an  upflow  furnace  or  under  a  counterflow 

furnace may be the same width as the furnace or 

may be one size larger than the furnace.  

Example: 

a “C” width coil may be installed with a “B” width 

furnace.

 For upflow applications, the front of the coil 

and furnace must face the same direction.

• 

If the furnace is installed in a residential garage, 

position the furnace so that the burners and ignition 

source are located not less than 18 inches (457 mm) 

above the floor. Protect the furnace from physical 

damage by vehicles.

• 

If  the  furnace  is  installed  horizontally,  ensure  the 

access  doors  are  not  on  the  “up/top”  or  “down/

bottom” side of the furnace.

• 

Do not connect this furnace to a chimney flue that 

serves a separate appliance designed to burn solid 

fuel. 

• 

On Counterflow Installations, the air conditioning coil 

must be downstream on the supply (positive) side 

of the furnace heat exchanger.

• 

Counterflow Installation over a noncombustible floor. 

Before setting the furnace over the plenum opening, 

ensure the surface around the opening is smooth 

and level. A tight seal should be made between the 

furnace base and floor by using a silicone rubber 

caulking compound or cement grout.

• 

Counterflow  Installation  over  a  combustible  floor. 

If  installation  over  a  combustible  floor  becomes 

necessary, use an accessory subbase (see 

Specification  Sheet  applicable  for  your  model  for 

details.) A  special  accessory  subbase  must  be 

used for upright counterflow unit installations over 

any  combustible  material  including  wood.  Refer 

to  subbase  instructions  for  installation  details. 

Follow the instructions with the subbase for proper 

installation.  Do  not  install  the  furnace  directly  on 

carpeting, tile, or other combustible material other 

than wood flooring. 

NOTE

: The subbase will not be required if an air conditioning 

coil is installed between the supply air opening on the furnace 

and the floor.

Clearances and Accessibility

NOTES:

• 

For servicing or cleaning, a 24” front clearance is 

required.

• 

Unit connections (electrical, flue and drain) may 

necessitate greater clearances than the minimum 

clearances listed above.

• 

In all cases, accessibility clearance must take 

precedence over clearances from the enclosure 

where accessibility clearances are greater.

NOTES:

• 

For servicing or cleaning, a 24” front clearance is 

required.

• 

Unit  connections  (electrical,  flue  and  drain)  may 

necessitate greater clearances than the minimum 

clearances listed above.

• 

In  all  cases,  accessibility  clearance  must  take 

precedence  over  clearances  from  the  enclosure 

where accessibility clearances are greater.

Содержание C9C96 Series





















































Отзывы: