Amana ALD 10D P1331011M Скачать руководство пользователя страница 34

Страница: 34 / 37

A–2

16400005

Dial Model - Quick Reference Guide

Refer to Product Safety Manual for Safety Statements

Complete Owner’s Manual available online

Quick Start Reference Guide

Oven Clearances

A—Allow at least 2" (5.1 cm) of clearance around top and sides of oven.

Proper air flow around oven cools electrical components. With restricted

air flow, oven may not operate properly and life of electrical parts is

reduced.

B—Allow at least 2" (5.1 cm) between air discharge on back of oven and

back wall.

No metal pans

DO NOT power spray

Part No.12891302

Printed 09/04

or full product documentation visit:

www.amanacommercial.com/wavelink

™

So...how do I use it?

Heating

1. Open oven door, place food in oven, and close oven door.

2. Turn the power level knob to desired power level.

•

Power level can be set at Low (17%), Defrost (33%), Medium (55%),

Med. High (77%), or High power (100%).

3. Turn time entry knob clockwise until desired time displays.

•

Cooking time can be set up to 10 minutes.

•

If turning the timer knob for less than 2 minutes, turn it past 2 minutes

and then back to the desired time.

4. Oven begins operation and time counts down.

5. When cooking time elapsed, microwave energy stops and oven signal

sounds.

Interrupting Operation

Open oven door to interrupt operation or turn time entry knob counterclockwise

to “0”. To resume microwave oven operation, close oven door.

If time was changed to “0”, time will need to be reset.

Changing Time and Power/Canceling

Mistakes

Cooking time and power level can be changed at any time while the oven is

operating. Turn knob(s) to desired new setting. To set cooking time to zero,

turn time entry knob counterclockwise to “0”.

Содержание ALD 10D P1331011M






































Результаты поиска

Содержание ALD 10D P1331011M

Отзывы:

Похожие инструкции для ALD 10D P1331011M

Бренды по названию

Популярные бренды

Amana ALD 10D P1331011M, Руководство по обслуживанию

Результаты поиска

Содержание ALD 10D P1331011M

Отзывы:

Похожие инструкции для ALD 10D P1331011M

Бренды по названию

Популярные бренды