Amana ALD 10D P1331011M Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 37

background image

Testing Procedures

!

WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to oven and discharge capacitor
before servicing, unless testing requires power.

16400005

©2009 ACP, Inc.

26

Illustration Component

Testing

Results

Thermal cutout

Disconnect all wires from TCO.
Measure resistance across terminals.
Cavity TCO .............................................

Magnetron TCO ......................................

Closed at 122ºF (50ºC) and
Opens at 185ºF (85ºC)
Closed at 249ºF (115ºC) and
Opens at 320ºF (160ºC)

Diode

Discharge Capacitor

Remove diode lead from capacitor and
connect ohmmeter.

Reverse leads for second test.

Infinite resistance should be
measured in one direction and 50K

Ω

or more in the opposite direction.

NOTE:

Ohmmeter must contain a

battery of 6 volts minimum.

Capacitor

Discharge Capacitor

Remove wires from capacitor terminals
and connect ohmmeter, set on highest
resistance scale to terminals.

Also check between each terminal and
capacitor case.

Between Terminals: Meter should
momentarily deflect towards zero
then return to over 5 M

Ω

. If no

deflection occurs, or if continuous
deflection occurs, replace capacitor.

Terminal to Case: Infinite resistance

Magnetron

Discharge Capacitor

Remove wires from magnetron and
connect ohmmeter to terminals. Also
check between each terminal and
ground.

Between Terminals: Less than 1

Ω

Each terminal to ground measures
Infinite resistance.

Note:

This test is not conclusive. If

oven does not heat and all other
components test good replace the
magnetron and retest.

Blower motor

Remove all wires from motor.

Measure resistance across coil ..............

Approximately 44

Ω

Stirrer motor

Remove all wires from motor.

Measure resistance across terminals .....

Approximately 3.8K

Ω

Secondary

Filament

Primary

Transformer

Discharge Capacitor

Remove all wires from terminals.

Measure resistance from:

Primary ..................................................
Filament.................................................
Secondary to Ground screw on
transformer stack...................................

Less than <1

Ω

Less than <1

Ω

Approximately 110

Ω

Dial timer

Remove leads from timer contact
terminals.
Measure resistance of following
terminals:

3 to 4

⎯

Timer in OFF position .................

3 to 4

⎯

Timer in ON position ...................

2 to 3

⎯

Timer in OFF or ON position ......

If timer does not indicate readings
below, replace timer.

Infinite

Ω

Approximately <1

Ω

Approximately 3.3 K

Ω

(timer motor)

Lamp and receptacle

Test continuity of receptacle terminals.

Indicates continuity with bulb
installed.

Wire Harness

Test continuity of wires

Indicates continuity

Electronic

control

board

Test interlock assembly switches.
Test cavity TCO.

If interlock switch assembly and
cavity TCO is operating correctly. If
the control board still has no display,
replace control board.

«
...
22
23
24
25
26
...
»

Содержание ALD 10D P1331011M






































Отзывы:

Нет отзывов

Похожие инструкции для ALD 10D P1331011M

Бренд: Kuppersbusch Страницы: 11

Бренд: Aurora Страницы: 16

Бренд: Oster Страницы: 34

Бренд: Daewoo Страницы: 28

Бренд: Cafe Страницы: 2

Бренд: Zephir Страницы: 15

Бренд: Daewoo Страницы: 39

Бренд: Marta Страницы: 18

TSCLTRDG1-AFS-026

Бренд: Calphalon Страницы: 17

Бренд: Gaggenau Страницы: 28

Бренд: GE Страницы: 32

Бренд: nardi Страницы: 39

Бренд: NEFF Страницы: 72

Бренд: ZANKER Страницы: 92

Бренд: Dacor Страницы: 8

Бренд: Tesco Страницы: 12

Бренд: Cleveland Страницы: 155

Combair V4000 45

Бренд: V-ZUG Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды