Amana ALD 10D P1331011M Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 37

background image

Disassembly Procedures

To avoid the risk of electrical shock, personal injury, or death,

disconnect power to oven and discharge the capacitors before

following any disassembly procedure.

©2009 ACP Inc.

16400005

27

High voltage is present at the high voltage terminal of

the high voltage transformer during any cooking cycle.
It is neither necessary or advisable to attempt

measurement of the high voltage.
Before touching any oven components or wiring, always

unplug the oven from its power source and discharge

capacitor.

Disconnecting Wire Terminals

All wire terminals are locking-type terminals.

Proceed as follows to disconnect wire terminals:

Insulated terminals:

Grasp insulator pod and pull back.

DO NOT PULL ON WIRE.

Non-insulated terminals:

Use a small blade screwdriver to depress locking-tab

and pull on terminal.

DO NOT PULL ON WIRE.

Outer Case

1. Disconnect power to oven.

2. Remove screws securing outer case to unit.

3. Slide outer case towards rear of unit.

4. Reverse procedure to reassemble.

During disassembly some foam gaskets may require

removal. These components must be replaced for

proper circulation of air over the components and

through the oven cavity.

«
...
25
26
27
28
29
...
»

Содержание ALD 10D P1331011M






































Отзывы:

Нет отзывов

Похожие инструкции для ALD 10D P1331011M

Бренд: GE Страницы: 32

Бренд: GE Страницы: 60

Бренд: GE Страницы: 20

Бренд: GE Страницы: 40

Бренд: GE Страницы: 40

Бренд: GE Страницы: 40

Бренд: GE Страницы: 34

Бренд: GE Страницы: 20

Бренд: GE Страницы: 20

Бренд: GE Страницы: 2

Бренд: GE Страницы: 48

Бренд: GE Страницы: 48

Бренд: GE Страницы: 72

Monogram ZSC1201NSS

Бренд: GE Страницы: 44

Advantium CSB913

Бренд: Cafe Страницы: 28

Бренд: GE Страницы: 2

Бренд: Magic Chef Страницы: 8

Бренд: Daewoo Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды