manualshive.com logo in svg

Amana AGR5712BD Series, Руководство по обслуживанию, Страница: 20 / 69

Поделиться
Скачать
Amana AGR5712BD Series Скачать руководство пользователя страница 20

Testing Procedures 

 

!

WARNING

 

To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing, 

unless testing requires power and/or gas. 

20 16026785 

© 2005 Maytag Services 

 

Control Feature 

Test 

Procedure 

Results 

NSC 

Twelve Hour Off 

Control will automatically cancel any 

cooking operation and remove all relay 

drives 12 hours after the last pad 

touch. 

See Sabbath mode to disable. 

NSC Diagnostic 

Code 

Display 

Press and hold 

More +

 pad for 3 to 5 

seconds when powering up the unit. 

Cycle through the codes using the 

More + 

or 

Less -

 pads. 

The last 5 diagnostic codes will be stored 

in the non-volatile memory. 

 

See 

"Description of Error Codes" 

for 

explanation. 

NSC One–Watt 

Standby 

Mode 

Press and hold 

Cancel

 and 

Less -

 

pads for 3 to 5 seconds. 

After 15 minutes in idle, the control will 

automatically enter this mode.  The LED 

display remains active during this mode. 

 

"Quick Test" Mode for NSC Control 

Follow procedure below to use the quick test mode. Entries must be made within 32 seconds of each other or the 

control will exit the quick test mode. 

4. 

Press and hold

 

Cancel

 and 

Broil

 pads for 3 to 5 seconds within 5 minutes of power

-

up. 

5.  Once the control has entered the 

"

Quick Test

"

 mode, release both pads. 

6.  Press each of the following pads indicated in the table below. 

NOTE:

  Press one of the following pads once to activate the response. 

Press the pad a second time to deactivate the response. 

NOTE:

  If the temperature sensor is greater than 400° F or if the temperature sensor reaches 400° F while under 

test, the Quick Test mode is disabled. 

Display will indicate the following: 

Key Operation 

[Bake] 

Bake

 relay activated 

[Broil] 

Broil

 relay activated 

[Timer] 

DLB 

relay activated 

[Clock] 

Alternate between 

ODD

 

LED

 

SEGMENTS

 and 

EVEN LED SEGMENTS

 on each keypress 

[More +] 

EEPROM

 version number 

[Less –] 

Code

 version number 

[Cancel] 

End Factory Test Mode 

Description of NSC Control Error Codes 

Error diagnostic codes can only be viewed by entering the Diagnostic Code Display Mode. 

Each error code consists of four digits and each digit is described in the following table. 

Digit Description 

1

st

 

Primary System: 

1 – Local to the control circuit board 

 

3 – Sensor or meat probe 

 

4 – Control input 

2

nd

 

Measurable: 

d – Diagnostic: measurable parameter 

 

c – Control related, replace control 

3

rd

 

Secondary System: Sequential numbering 

4

th

 

Oven Cavity: 

1 – Oven 

 

c – Control specific 

Enter Diagnostic Code Display Mode by pressing 

More +

 pad for 3 to 5 seconds within 30 seconds of powering 

up the control.

 

Содержание AGR5712BD Series






































































Отзывы:

Нет отзывов