background image

7

A. This appliance does not have a pilot. It
is equipped with an ignition device which

try to light the burners by hand.

automatically lights the burners. Do not

the appliance area for gas. Be sure to
smell next to the floor because some gas
is heavier than air and will settle on the

do not use any telephone in your

Do not touch any electric switch;

Do not try to light any appliance.

WHAT TO DO IF YOU SMELL GAS

the gas suppliers instructions.

from a neighbor's phone. Follow

Immediately call your supplier

1. STOP! Read the safety information

2. Set the thermostat to lowest setting.

4. This appliance is equipped with an
automatic  ignition  system  which

3. Turn off all electric power to the

6. Move the gas control switch or knob

5. Remove control access panel.

automatically lights the burners. Do not
try to light the burners by hand.

B. BEFORE OPERATING smell around

FOR YOUR SAFETY READ BEFORE OPERATING

SWITCH SHOWN
IN "ON" POSITION

GAS CONTROL

3. Remove control access panel.

appliance if service is to be performed.

2. Turn off all electric power to the

or  any  other  appliance.

FOR  YOUR  SAFETY

1. Set the thermostat to its lowest setting.

TO TURN OFF GAS TO APPLIANCE

other  flammable  vapors  and  liquids  in  the  vicinity  of  this

to "OFF".

above on this label.

appliance.

building.

floor.

instructions,  this

setting.

  Do  not  store  or  use  gasoline  or

4. Move the gas control switch or knob

follow the instructions "To Turn Off Gas

5. Replace control access panel.

To  Appliance"  and  call  your  service

12. If  the  appliance  will  not  operate,

to "OFF". Do not force.

technician or gas supplier.

in  fuel  combustion

you  to  substances

death  or  serious

which  can  cause

illness  and  which

cause cancer, birth
defects  or  other
reproductive harm.

are  known  to  the

This product contains
fiberglass  insulation.

State of California to

product could expose

California  to  cause

known by the State of

contains  a  chemical

Fiberglass  insulation

cancer.

0140F00688 Rev A

call  a  qualified  service  technician.

will not operate, don't try  to  repair it,

gas. If  you  then  smell  gas,  STOP!

8. Move the gas control switch or knob

above on this label. If  you  don't  smell

Follow  "B"  in  the  safety  information

7. Wait five (5) minutes to clear out any

the control system and any gas control

the appliance and to replace any part of

a qualified service technician to inspect

has been under water. Immediately call

D. Do not use this appliance if any part

tools. If the gas control switch or knob

control   switch  or  knob.  Never   use

C. Use only your hand to move the gas

which has been under water.

If you do not follow these instructions exactly,
a fire or explosion may result causing property

If you cannot reach your gas supplier,

damage, personal injury or loss of life.

Force or attempted repair may result in

10. Turn  on  all  electric  power  to  the

11. Set  the  thermostat  to  the  desired

9. Replace control access panel.

a fire or explosion.

to "ON".

OPERATING INSTRUCTIONS

gas, go to the next step.

appliance.

call the fire department.

or  additional information
consult a qualified

or the gas supplier.

WARNING:

and maintained in

manufacturer's

installed,  operated

accordance with the

of local codes, follow

codes. In the absence

with the manufacturers
instructions and local

This furnace must be
installed in accordance

Code, ANSI Z223.1.

the National Fuel Gas

installer, service agency

If not

WARNING:

cause   injury   or

Refer to the user's
information manual
provided with this

property damage.

maintenance  can

furnace. For assistance

alteration, service or

installation,  adjustment,

Improper

IMPORTANT INFORMATION

Содержание ACSS9 Series




























































Отзывы: