VEND-10, 11 Programming Instructions
RE220002 Rev. 6`
44
To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge the capacitor
before following any disassembly procedures.
WARNING
!
VEND-10.C, .F, .G, .H, .J, .K, .L, VEND-10,
VEND-11
To reprogram the times you want:
1. Open the oven door, leave it open.
2. Enter the programming code "614" (push buttons 6, 1
and 4).
3. Close the oven door, note "PROG" in the display
which indicates you are in the programming mode.
If you make an error while programming, push the "0"
button once to clear the error. Go back to the
programming step you were performing.
For each button to be programmed:
4. Push the button to be reprogrammed. Note that the
button number and first stage programmed time
appear in the display.
5. To change cook times:
Push and hold in button 1
to change seconds
"00:01"
Push and hold in button 2
to change tens of seconds
"00:10"
Push and hold in button 3
to change minutes
"01:00"
Push and hold in button 4
to change tens of minutes
"10:00"
NOTE:
If you miss the number you want, continue to
hold. Momentary pushes will advance the count
one number at a time.
6. To select 100% power, push the start button; to select
Defrost II, push the Defrost II button.
7. Push button 5 to move to the next step. The display
will show the previously set second stage time.
8. To change second stage time, repeat step 5 above.
9. Defrost II is not an option in the second stage. The
second stage will always be full power.
10. Push button 5. Programming of the button is
complete.
Example: If you select 2:00 of "Defrost II" plus 1:00 of
100% power on a button, the total cycle time will
equal 3:00 for that button. The oven will defrost
for two minutes and heat for one minute to heat
the food from frozen to ready, per your instruc-
tions.
11. Go back to steps 4 - 10 for the next button to be
programmed.
12. When you have completed programming the buttons
you wish to change, open and close the oven door to
exit the programming mode and go back to normal
operation.
Cook Count
To use the "Cook Count" feature:
1. Open the oven door; leave it open.
2. Enter the access code "613" to begin the "Cook
Count" mode (push buttons 6, 1 and 3).
3. Close the oven door.
4. The oven display will show "Count" and will provide
the total number of heating cycles for all 10 buttons
combined.
5. Push each button to obtain the count for that specific
button.
6. After obtaining the counts, open the oven door to exit
the "Cook Count" mode or let the oven shut itself
down (in 60 seconds).
How to Use the Change Time Feature
1. Open the oven door, place food on shelf and close
the door.
2. Push the change time button.
3. Use buttons 1 through 0 to enter the time (up to
39:59). Example: Push 2, 4 and 0 for 2:40.
4. To start the cook cycle, push start for 100% power or
Defrost II.
5. If the door is opened, the cooking cycle will stop. To
resume cooking, close the door and press the
desired button.
Volume Adjustment for End-of-Cook Cycle
Tone
1. Open the oven door; leave it open.
2. Press buttons 6, 1 and 6.
3. Close the door and "Off", "Low", "Medium" or "High"
will appear in the display.
4. To change volume to "Off", press button 1.
To change volume to "Low", press button 2
To change volume to "Medium", press button 3.
To change volume to "High", press button 4.
5. Open and close the oven door to revert to normal
operation.