manualshive.com logo in svg

Amana A1200S, Сервисная инструкция, Страница: 40 / 75

Поделиться
Скачать
Amana A1200S Скачать руководство пользователя страница 40

RE220002 Rev. 6`

40

Troubleshooting Procedures

To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge the capacitor
before following any disassembly procedures.

WARNING

!

Test S equenc e 2:  COOK CONDITION 

Open door, place container of water in 
oven (1000 m l). 

Note: Conditional S chematic for Cook  Condition shown on          

next page.

Initiate cook c ycle.

Control W ill Not P rogram

1. Inoperative touch panel assembly.
2. Inoperative circuit board.

Controller beeps when data is entered,

No

Control P rograms  But W ill Not Count Down

dis play counts down?

1. 
2.

Inoperative interlock switch module (door s ens e test). 
Inoperative circuit board.

Yes

Cavity  Light on? Blower motor operates ?

No

1. Inoperative electronic  control circuit board assembly.
2. Interlock Switch Module inoperative or out of adjus tment.  

Yes

(P rimary or S econdary test).

3. 
4.

Blower m otor inoperative or binding.                       
Broken or loose wire connec tion.

Stirrer blades  rotate?

No

1. Inoperative stirrer sys tem .

2. Broken or loose wire connec tion.

Yes

Display c ounts down to zero, display 
shows  "DONE " and control beeps.

No

1.
2.

Inoperative electronic  control circuit board assembly. 
Broken or loose wire connec tion.

Heats   Very  S lowly

Note:  Verify by performing power tests .

Yes

1.
2. 
3.

Voltage s elec tor plug (FS17 and FS 20 only ).                     
Low line voltage.
Inoperative power transformer.

Open oven door; water placed in oven 
cavity  was heated?

No

4.
5. 
6. 
7. 

Inoperative capac itor.
Inoperative m agnetron.                                                    
Inoperative diode.                                                            
Broken or loose wire connec tion.

No Heat

Yes

1.
2.
3.
4.
5.
6. 
7.

Inoperative diodes.
Inoperative capac itors.
Inoperative m agnetrons.
Inoperative transform ers.                                                  
Inoperative circuit board.
Inoperative triac.                                                             
Broken or loose wire connec tion.

Cook operation norm al; proc eed to             
Power Level c ondition.
Test S equenc e 3, previous page .

Troubleshooting Flow Chart for Units with Electronic Timers

Models  P130210_M Series

Содержание A1200S












































































Отзывы:

Нет отзывов