manualshive.com logo in svg

Amana A1200S, Сервисная инструкция, Страница: 23 / 75

Поделиться
Скачать
Amana A1200S Скачать руководство пользователя страница 23

23

RE220002   Rev. 6

Disassembly Procedures

To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge capacitor(s)
before following any disassembly procedures.

WARNING

!

Interlock Switch Module Adjustment

1. Remove the control panel assembly.
2. Loosen the two screws that mount the interlock

switch module to the cavity assembly.

3. With the oven door closed, align the switch module to

the door hook to provide maximum activation of the
switch actuator.

4. Retighten module mounting screws.
5. Check the oven for proper door closure and switch

operation.

6. Check the oven for proper operation and radio

frequency leakage around the door.

Door Disassembly

1. Remove door from oven as described in DOOR

REPLACEMENT AND ADJUSTMENT in this section.

2. Place door front down on a flat protected surface with

the door handle extending over the edge of the
surface.

3. Peel off the adhesive mounted inner window.
4. Remove door screen mounting screws and remove

door screen.

5. Remove outer window.
6. Remove door filler.

Door Assembly

1. Place door, front down, on a flat protected surface

with the door handle extending over edge of surface.

2. Install outer window.
3. Mount door screen and door filler on outer door.
4. Install door screen mounting screws keeping outer

door as flat as possible.

5. Install adhesive mounted inner window.

6. Install door on hinges as described under DOOR

REPLACEMENT AND ADJUSTMENT  in this
section.

7. Check the oven for proper operation.  Check for radio

frequency leakage around the door.

Exhaust Transition Duct Replacement

1. Lower the back panel to the service position.
2. Pull the duct toward the oven rear.
3. Rotate the bottom of the duct clockwise to remove.
4. To replace, insert rib on wrap into slot on top of duct.

Lift up on bottom tabs on duct and rotate bottom of
duct counterclockwise to secure tabs to lower rail on
wrap.

5. Slide duct toward oven front.

Содержание A1200S












































































Отзывы:

Нет отзывов