manualshive.com logo in svg

Amana A1200S, Сервисная инструкция, Страница: 25 / 75

Поделиться
Скачать
Amana A1200S Скачать руководство пользователя страница 25

25

RE220002   Rev. 6

Disassembly Procedures

To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge capacitor(s)
before following any disassembly procedures.

WARNING

!

Blower Replacment

1.

Remove magnetron inlet duct.

2.

Remove blower motor ground lead screw from the
oven base.

3. Disconnect two blower motor wires.
4. Remove mounting screws and lift out blower

assembly.  The left blower assembly (FS14 only) has
two mounting screws located toward the rear of the
oven.  The right blower asseembly has two mounting
screws toward the rear of the oven and one mounting
screw near the high voltage transformer.

Right (Rear) High Voltage Transformer
Replacement

1. Lower the back panel to the service position.
2. Remove the right blower air duct and the magnetron

exhaust duct (FS14 only).

3. Disconnect the transformer leads.
4. Remove four transformer mounting screws.

Left (Side) High Voltage Transformer
Replacement

1. Lower the back panel to the service position.
2. Remove the left blower air duct and left blower

assembly.

3. Disconnect the transformer leads.
4. Remove two transformer mounting screws.

Component Module Panel Removal

Model VEND-10.000, .A, .B, .C
1. Remove the control panel assembly.
2. Locate the top and bottom release tabs on the panel

harness connector located above and to the rear of
the component module panel.  Press the tabs against
the connector housing and pull the connector toward
the oven front to disconnect the connector.

3. Remove two interlock switch module screws and

remove the switch module.  Do not disconnect wires
to the switch module.

4. Remove the nut at the top of the component module

panel.  Pull the top of the panel away from the cavity
wall until it clears the stud.

5. Pull the component module panel toward the front of

the oven and lift up to separate the two tabs from
slots in the oven base.

6. Slowly pull the interlock switch module and

component module panel through the control panel
opening.  Move wires around as required to clear the
opening.

NOTE: After replacement, perform interlock switch

module adjustment.  Perform Radio Frequency
Leakage Test Procedures.

Содержание A1200S












































































Отзывы:

Нет отзывов