background image

Page 12 

For Assistance: [email protected]  +1 (909) 591-8431 PUD4146R1-0

EDM Installation and Maintenance Instructions

J5 Output Contacts

Pin #

Pin  
Name

Function 
Description

Contact 
Type

Function & Behavior 
Description

Pin #

Pin  
Name

Function 
Description

Contact 
Type

Function & Behavior 
Description

1

ENTUCX

Exit Passage 

Count

MDC

Counts the number of 

passages in the exit direction.

1

EXTPAS

Free 

Passage 

CCW

SDC

Sets the turnstile to Free 

Passage mode in the CCW

direction.

2

ENTACX

Entry 

Passage 

Count

MDC

Counts the number of 

passages in the entry 

direction.

2

EXTREJ

Bad Card 

CCW

MDC

Illuminates the CCW direction 

RED User Status Icon for 2 

seconds.

3

GNDX

Ground

N/A

Common input ground signal.

3

EXTACC

Good Card 

CCW

MDC

Opens the turnstile for one 

authorized passage until 

passage occurs or timeout.

4

4

EMROVR

Emergency 

Override

SDC 

(N.O. or 

N.C.)

Drops the arms for free egress.

 

Arms remain down and turnstile  

is inactive until SDC is removed, 

or contact is reestablished 

if N.C. setting is enabled.

(Typically used for fire alarm

or life safety systems.) 

5

5

GND

Ground

SDC

Common input ground signal.

6

6

BARDISABLE Barrier 

Disable 

Mode

7

7

ALRRST

SDC

Changes the EMROVR contact  

from N.O to N.C.

8

8

ENTSER

No Passage 

Mode CCW

SDC

Sets the turnstile to No 

Passage mode in the CCW

direction.

9

9

ENTOVR

N/A

N/A

Not available in the EDM.

10 GND

Ground

N/A

Common input ground signal

10

11 ENTCLS

No Passage 

Mode CW

SDC

Sets the turnstile to No 

Passage mode in the CW

direction.

11

12 ENTPAS

Free 

Passage 

Mode CW

SDC

Sets the turnstile to Free 

Passage mode in the CW

direction.

12

13 ENTREJ

Bad Card 

CW

MDC

Illuminates the CW side 

RED User Status Icon for 2 

seconds.

13

14 ENTACC

Good Card 

CW

MDC

Opens the turnstile for one 

authorized passage until 

passage occurs or timeout.

14

15 GND

Ground

N/A

Common input ground signal.

 

Emergency 

Override State

Arm drops to allow for 

barrier free operation. 

J4 Terminal Block Input Contacts

MDC

Control Board Description (Cont.)

J5 Terminal Block Output Contacts 

J4 Input Contacts

Pin #

Pin  
Name

Function 
Description

Contact 
Type

Function & Behavior 
Description

Pin #

Pin  
Name

Function 
Description

Contact 
Type

Function & Behavior 
Description

1

ENTUCX

CCW 

Passage 

Count

MDC

for each rotation in the CCW 

direction.

1

EXTPAS

Free 

Passage 

Exit

SDC

Sets the turnstile to Free 

Passage mode in the exit 

direction.

2

ENTACX

CW

Passage 

Count

MDC

for each rotation in the CW

direction.

2

EXTREJ

Bad Card 

Exit

MDC

Illuminates the exit direction 

RED User Status Icon for 2 

seconds.

3

GNDX

Ground

N/A

Common input ground signal.

3

EXTACC

Good Card 

Exit

MDC

Opens the turnstile for one 

authorized passage until 

passage occurs or timeout.

Emergency 

Override

SDC 

(N.O. or 

N.C.)

**Opens the barriers toward 

the unsecured side; barriers 

remain open and turnstile is 

inactive until SDC is removed, 

or contact is reestablished 

if N.C. jumper is enabled. 
or life safety systems.)

Ground

SDC

Common input ground signal.

Barrier 

Disable 

Mode

N/A

**Disables the barrier.

**

SDC

Sets the EMROVR contact to 

N.O or N.C.

No Passage 

Mode Exit

SDC

Sets the turnstile to No 

Passage mode in the exit 

direction.

N/A

N/A

Not available in the EDM.

Ground

N/A

Common input ground signal

No Passage 

Mode Entry

SDC

Sets the turnstile to No 

Passage mode in the entry 

direction.

Free 

Passage 

Mode Entry

SDC

Sets the turnstile to Free 

Passage mode in the entry 

direction.

Bad Card 

Entry

MDC

Illuminates the entry side 

RED User Status Icon for 2 

seconds.

Good Card 

Entry

MDC

Opens the turnstile for one 

authorized passage until 

passage occurs or timeout.

Ground

N/A

Common input ground signal.

Outputs a dry-contact closure

Outputs a dry-contact closure

Identifying Rotation Direction

Clockwise (CW):
Turnstile arms rotate in a clockwise direction when viewed 

looking down from behind the cabinet.

Counter-Clockwise (CCW):
Turnstile arms rotate in a counter-clockwise direction when 

viewed looking down from behind the cabinet.

CW

Secured 

Side

CCW

Unsecured 

Side

Fig. 10

Orientation shown for a right-handed cabinet.

Adjacent Barrier or Turnstile

Содержание EDM



































Отзывы:

Похожие инструкции для EDM