Alvarado CLST-3 Скачать руководство пользователя

Страница: 7 / 46

MST Installation Instructions

Installation Instructions [email protected] +1(909) 591-8431 www.alvaradomfg.com

Page 7

Turnstile

Center

Installation Instructions

NOTE

Install the turnstile on a 6' x 6' (min.) level concrete slab. The slab must

be a minimum of 4" thickness. The turnstile may only be installed on

concrete. Do not install the turnstile on asphalt.
DIMENSIONS SHOWN ARE FOR MST-3 and MST-6X MODELS. SEE

APPENDIX A-D FOR OTHER MODELS.

NOTE

The turnstile is rated for both indoor and outdoor use.

Installation Locations

Determine where the turnstile will be installed.

Consider the overall footprint size of the unit when

determining the installation location (Figure 1).

Once the installation location has been determined,

use a chalk line to mark the centerline of the

turnstile.

NOTES

Default entry rotation is counterclockwise.

Confirm correct entry direction prior to

installation.
Alvarado recommends that the minimum

installation width required be 64".

62.00"

(1575mm)

54.00"

(1372mm)

Determine and mark the centerline location for the

OV, Roto, and Yoke (Figure 2).

NOTE

The overall height of the MST is 91.5". However, an

additional 3" of clearance must be added for service

and maintenance.
If desired, installers can stub up the power conduit at

the intersection of the turnstile centerline and the OV

centerline. Power may also be routed directly into the

top channel (Figure 26).
Mark all center lines prior to installation.

Fig. 1

Fig. 2

Roto Centerline

29.63"

(752mm)

30.0"

(762mm)

Yoke Centerline

Entry Side

(Unsecured)

Exit Side

(Secured)

31.5"

(800mm)

30.5"

(775mm)

OV Centerline

30.0"

(762mm)

29.63"

(752mm)

Содержание CLST-3















































Результаты поиска

Содержание CLST-3

Отзывы:

Похожие инструкции для CLST-3

Бренды по названию

Популярные бренды

Alvarado CLST-3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CLST-3

Отзывы:

Похожие инструкции для CLST-3

Бренды по названию

Популярные бренды