Alvarado CLST-3 Скачать руководство пользователя | Manualshive

Страница: 32 / 46

background image

MST Installation Instructions

Page 32 [email protected] +1(909) 591-8431 www.alvaradomfg.com

Installation Instructions

Fig. 36

Upper

Shaft

Bearing

Slide Rods

Lubrication (Cont)

Fig. 38

Self-Centering Mechanism (Figure 38)

Clean and lubricate the two slide rods using DuPont

Teflon Non-Stick Dry-Film Lubricant. Place 2 to 3 drops

of DuPont Teflon Non-Stick Dry-Film Lubricant along the

shaft of the slide rods. Rotate the turnstile 4 to 5 times to

ensure the lubricant is spread evenly along the slide rods.

Fig. 37

Lower

Shaft

Bearing

Main Cam and Lower Shaft Bearing (Figure 37)

Lubricate the grease fitting on the lower shaft bearing

using the recommended grease and a grease gun.

Main Cam and Upper Shaft Bearing (Figure 36)

Lubricate the grease fitting on the upper shaft bearing

using the recommended grease and a grease gun.

Solenoid

Spring

Lock Arm

Return

Spring

Fig. 35

Springs (Figure 35)

Lubricate spring contact points with DuPont Teflon Non-

Stick Dry-Film Lubricant. Place lubricant on spring body

by adding 1 drop on contact points.

«
...
30
31
32
33
34
...
»

Содержание CLST-3















































Отзывы:

Нет отзывов

Похожие инструкции для CLST-3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды