Alvarado CLST-3 страница 39 Скачать руководство пользователя

Страница: 39 / 46

MST Installation Instructions

Installation Instructions [email protected] +1(909) 591-8431 www.alvaradomfg.com

Page 39

Appendix E -

Fail-lock / Fail-safe Spring and Solenoid Configurations

Fail-safe

Fail-lock

Clockwise

Fail-lock / Fail-safe Spring and Solenoid Configurations - Adjustable

Solenoid

NOTE

For use with turnstiles that utilize adjustable solenoid mounting positions.

Spring Configuration

Solenoid Mount Position

A - Return Spring
B - Solenoid

Spring

CW Lock

Arm

Fail-safe

Solenoid

(Black)

(Red)

Fail-lock

Solenoid

CW Lock

Arm

A - Return Spring
B - Solenoid

Spring

(Black)

(Silver)

Spring Configuration

Solenoid Mount Position

NOTES

Spring & Solenoid Operations are contingent on

the lock arm tabs being square to the lock arm body.
With exception to fail-lock clockwise (

), the solenoid will be

mounted to the back of the slots. Then the lock arm tab will

be used to adjust the spring tension (see illustration to the

right).

Solenoid mounting screws must be tightened to 30 in-lbs.

to avoid slippage from continuous use.

Tab parallel to

lock arm

Tab perpendicular

to lock arm

Screw is all the

way to the rear

Содержание CLST-3















































Результаты поиска

Содержание CLST-3

Отзывы:

Похожие инструкции для CLST-3

Бренды по названию

Популярные бренды

Alvarado CLST-3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CLST-3

Отзывы:

Похожие инструкции для CLST-3

Бренды по названию

Популярные бренды