Alvarado CLST-3 Скачать руководство пользователя

Страница: 5 / 46

MST Installation Instructions

Installation Instructions [email protected] +1(909) 591-8431 www.alvaradomfg.com

Page 5

This product is shipped with all required installation hardware and components. Make sure that none of these parts

are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the

installation and contact Alvarado.

Yoke

(Qty 1)

MST Illustrated Parts List

Parts List

Roto

(Qty 1)

Yoke Guard Plate

(Qty 1)

Bottom Bearing

Plate (Qty 1)

Bottom Bearing

Cover (Qty 1)

Bottom Bearing

(Qty 1)

Top Channel

(Qty 1)

10-32 x ½" Allen Head

Screw (Qty 6)

½" x 1" Hex Head

Bolt (Qty 1)

½" x 1½" Hex Head

Bolt (Qty 2)

½" x 2¾" Hex

Bolt Head (Qty 2)

#10 x ¾" Phillips Pan Head

Screw (Qty 10)

½" Nut

(Qty 5)

⅜" x 2½" Anchor Bolt

(Qty 12)

⅜" Flat Washers

(Qty 12)

⅜" x 2.00" Concrete Anchors

(Qty 12)

Top Bearing

Cover (Qty 1)

⅜" x 4½" Anchor Bolt

(Qty 3) - Yoke Only

NOTE

Alvarado full height turnstiles share common components across models. The parts list below is

for the MST-3 and MST-6X models only. Reference appendix A-D to see alternate components

used on other models.

½" Flat

Washer (Qty 1)

Concrete Anchor Package

NOTE

For stainless steel installations, discard the 2½" zinc anchor bolts and ⅜" zinc flat washers packaged

with the concrete anchors. Use the supplied 2½" stainless steel anchor bolts and ⅜" stainless steel

flat washers.

½" Lock

Washer (Qty 5)

Содержание CLST-3















































Результаты поиска

Содержание CLST-3

Отзывы:

Похожие инструкции для CLST-3

Бренды по названию

Популярные бренды

Alvarado CLST-3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CLST-3

Отзывы:

Похожие инструкции для CLST-3

Бренды по названию

Популярные бренды