16
L
Pay attention to the correct running direction of the saw blade:
The arrow on the safety guard and the arrow on the saw blade must
show to the same direction.
9.
Reinstall the front saw blade flange and the washer.
10.
Secure the saw blade using the screw.
11.
Slide the washer (9) on the support pin (10).
12.
Lift the tilt table (2), guide the support pin (10) into the hole (A)
and secure the tilt table using the transport safety device (3).
13.
Slide first the rubber washer (9A) on the support pin (10), then
the large washer (9) and at last the small washer (9B).
14.
Screw the nut M16 (4) on the support pin (10) again.
15.
When screwing the nut M16 (4) on the support pin (10)
make sure that the distance between saw blade and tilt table (2) is at
least 50 mm.
16.
Re-attach the cover plate (12).
17.
Remove the locking pin (13).
Replacing the plastics insert
Immediately replace the worn or damaged plastics inserts (18).
1.
Loosen the screws of the plastics insert and remove them.
2.
Insert a new plastic insert and screw it tightly in place.
Replacing
the
recuperating
spring
Immediately replace a worn or damaged recuperationg spring.
1.
Remove the screw from the cover plate (12).
2.
Secure the tilt table (2) using the transport safety device (3).
Remove the nut M16 (4) and the three washers (9B + 9 + 9A). When
doing so, firmly hold the tilt table.
3.
Remove the transport safety device (3) and slowly lower the
tilt table towards the ground.
4.
Remove the washer (9) and the saw blade recuperating spring
(11).
5.
Slide a new recuperating spring on the support pin (10) and then
the washer (9).
6.
Lift the tilt table and guide the support pin into the hole (A).
7.
Slide first the rubber washer (9A) on the support pin (10), then
the large washer (9) and at last the small washer (9B).
8.
Screw the nut M16 (4) on the support pin (10) again.
9.
When screwing the nut M16 (4) on the support pin (10)
make sure that the distance between saw blade and tilt table (2) is at
least 50 mm.
10.
Re-attach the cover plate (12).
Replacing / Tensioning the V-belt
Immediately replace a worn out or broken V-belt.
1.
Remove the three screws of the V-belt cover (22) and remove the
latter.
2.
Check the tension of the V-belt (21). In tensioned condition, you
should be able to press it down by approx. 8 mm.
3.
To tension and release the V-belt (21) loosen the four
hexagon screws and tighten (tension) or loosen (release) the two
tensioning screws M10x120.
4.
When replacing the V-belt (21) loosen the tensioning screws
M10x120 so that you can wrap the new V-belt (21) around the large and
the small guide roller.
5. Tension the V-belt (21) as described under 2. and 3. and re-tighten the
four hexagon screws.
6.
Re-attach the V-belt cover (22) using the screws provided for this.
Transport
Disengage the PTO before each transport.
L
Before each transport:
1.
Push the tilt table towards the saw blade.
2.
Hook in the transport safety device (3) and secure it using
the spring pin (29).
Transport with the transport arm (28)
Secure the transport arm (28) to three-point hitch (23).
Flip up the transport arm (28), slightly lift the log saw and
push it on the wheels (1) before you.
Transport with the three-point hitch (23)
Before transporting make sure that the PTO operation is
deactivated and the PTO shaft is hooked in the safety chain (25).
Secure the machine to the tractor's three-point hitch (category 1 /
2).
If you transport the machine on the three-point hitch
(category 1 / 2) of a tractor (or similar equipment) and lighting or
signalling devices (such as brake, rear and flashing lights) are
covered by the attachment, you have to install an additional
electrical lighting assembly to be allowed to use public traffic
routes. This also applies to units that jut out more than 40 cm on
the sides or more than 1 m on the rear from the edge of the
tractor's effective reflex surface (light-exit surface). In addition to
this, the tractor must have clearance lamps on its front if
attachments jut out more than 40 cm from the sides. According to
DIN 11300, any parts of fitted or towed attachments posing a
traffic hazard must also permanently carry red-white striped
warning plates.
For up-to-date information see the current road traffic act.
Bear in mind that front ballast has to be attached when this
machine is transported by a tractor (steerability) if this is required
according to the weight table for the tractor.
Do not exceed a maximum transport speed of 30 km/h.
Storage
Disengage the PTO shaft from
the machine.
Store unused equipment in a dry, locked place out of the reach of
children.
Before a longer period of storage carry out the following to extend the
saw service life and ensure an easy operating:
−
thoroughly clean the device
−
treat all movable parts with an environmentally friendly oil
L
Never use any grease!
Содержание WSL 700 PTO
