
15
Working with the saw
Before starting to work consider the following safety advices to keep
the risk of injuries as small as possible.
Saw blade, plastic inserts, recuperating spring o. k.
Workplace tidied?
You may not start to operate the machine until you have read these
operating instructions, observed all the instructions given and
installed the machine as described!
Before making adjustments to the saw settings (e.g. replacing the
saw blade etc.)
−
Stop and switch off the tractor. Pull off the ignition switch.
−
wait for standstill of the saw blade
−
Disengage the PTO shaft from the machine.
Also, note the following important points:
Place yourself outside of the area of danger.
Place the wood piece in the jigging device. Cut through the piece with
uniform pressure.
Never remove loose splinters, chips, or similar by hand.
At any case pay attention to all safety instructions.
Working instructions
1.
Secure the saw against rolling away.
2.
Place the wood piece in the jigging device.
It is possible to cut wood with a diameter of min. 80 mm to max.
240 mm are allowed to be sawed.
You will get pieces of equal length if you pull out the length
stop (26) and fix it in the desired position using the machine knob (27)
3.
Hold the handle (14) on the jigging device with both hands and push
the jigging device uniformly towards the saw blade. Avoid erratic
movements.
L
The barbs on the jigging device prevent any turning of the wood
piece during sawing.
Do not force the jigging device against the saw blade, the motor
speed should not drop too far.
4.
After cutting, the jigging device is automatically brought back to its
home position by spring force.
L
If the recuperating spring (11) is broken or worn, the jigging
device will not automatically return to its home position. Replace the
recuperating spring. See “Replacing the return spring”.
Never saw without or with a damaged recuperating spring.
5.
Only advance the wood piece after a completed sawing operation.
Conduct in case of accident or failure
1.
Stop and switch off the tractor. Pull off the ignition switch.
2.
Wait until the saw blade comes to a dead stop.
3.
Disengage the PTO shaft from the machine.
4.
Initiate first aid actions in the event of injuries.
Conduct in the case of blocked saw blade due to
stuck wood pieces
1.
Stop and switch off the tractor. Pull off the ignition switch.
2.
Disengage the PTO shaft from the machine.
3.
Remove the blockage.
Wear protective gloves.
Do not remove the stuck wood piece with your hands but using a
suited wood piece.
4.
Check the saw blade for any damages.
Maintenance and cleaning
Before each maintenance and cleaning work
−
Stop and switch off the tractor. Pull off the
ignition switch.
−
Wait unitl the saw blade comes to a stop
−
Disengage the PTO shaft from the machine.
Maintenance and repair work other than those described in this chapter is
only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected damages
and injuries.
Cleaning
L
Observe the following to maintain the operability of the
machine:
Do not wash down device with water.
Remove shavings and dust only with a brush or vacuum cleaner.
Clean and oil all moving parts regularly.
L
Never use any grease!
Use for instance sewing machine oil, liquid hydraulic fluid or
environmentally acceptable spray oil.
Take care that the saw blade remain free of rust and resin.
Remove resin residues from the push frame surface.
Resin residues can be removed with a commercial maintenance and
care spray.
The saw blade is a wearing part and will become dull after prolonged
or frequent use.
Renew the saw blade or have it sharpened.
Maintenance
Changing the saw blade
Disengage the PTO shaft from the machine
before changing the saw blade.
Danger of cutting!
The saw blade is massive and it could be to
slick. Wear gloves when replacing the saw blade.
Do not use any saw blades made of HSS steel.
Do not use any cracked saw blades or such that have changed their
shape.
Only use well-sharpened saw blades.
Danger of burning!
The saw blade is still hot shortly after cutting.
1.
Remove the screw from the cover plate (12).
2.
Secure the tilt table (2) using the transport safety device (3).
Remove the nut M16 (4) and the three washers (9B + 9 + 9A). When
doing so, firmly hold the tilt table.
3.
Remove the transport safety device (3) and slowly lower the
tilt table towards the ground.
4.
Use the locking pin (13) to secure the saw blade (5) against
turning. Select the matching hole according to the size of your saw
blade (Ø 600 mm / Ø 650 mm / Ø 700 mm).
5.
Loosen the screw (6).
6.
Remove the washer (7), the front saw blade flange (8) and the
saw blade (5).
7.
Clean the saw blade flanges (8, 15).
8.
Install a new or sharpened saw blade.
Содержание WSL 700 PTO
