6.APPENDIX
LTO DRIVE2.3 Midi standard control
PROGRAM CHANGE
Parameter
Value
Legend
Preset 01
0
Factory Preset
Preset 02 to preset 65
1, 2, 3,......, 64
User Preset
CONTROL CHANGE
Parameter
Controller
Value
setting
Legend
Bank
0
0, 1, 2
Mode Channel
Mode Channel
22
22
0, 1
2, 3, 4, 5
Input Left, Input Right
Output 1, 2, 3, 4
Output Volume
7
0,..., 48
Select Mode Channel
12 /
12 dB
High Pass Filter
High Pass Filter
17
17
0,..., 120
0, 1, 2, 3, 4
Mode Channel = 2, 3, 4, 5 Bank=0
Mode Channel = 2, 3, 4, 5 Bank=1
HP Frequency
HP Order
Low Pass Filter
Low Pass Filter
18
18
0,..., 120
0, 1, 2, 3, 4
Mode Channel = 2, 3, 4, 5 Bank=0
Mode Channel = 2, 3, 4, 5 Bank=1
LP Frequency
LP Order
Delay Line Adj
Delay Line Fine
19
19
0,..., 127
0,..., 95
Mode Channel = 0, 1, 2, 3, 4, 5 Bank=0
Mode Channel = 0, 1, 2, 3, 4, 5 Bank=1
508 ms step 4ms
1995 us step 21us
Limiter Threshold
Limiter Release
Limiter Attack
20
20
20
0,..., 29
0,..., 3
0,..., 3
Mode Channel = 2, 3, 4, 5 Bank=0
Mode Channel = 2, 3, 4, 5 Bank=1
Mode Channel = 2, 3, 4, 5 Bank=2
0, ...,
55dB
0.4s, 0.5s, 0.7s, 1.4s
0.05s, 0.1s, 0.2s, 0.3s
Polarity
Polarity
21
21
0
1
Mode Channel = 2, 3, 4, 5
Mode Channel = 2, 3, 4, 5
Direct
Invers
Filer 01, 02, ..., 04
Filer 01, 02,..., 04
Filer 01, 02,..., 04
12, 13, 14, 15
12, 13, 14, 15
12, 13, 14, 15
0,..., 120
0,..., 60
0,..., 59
Only Mode Channel = 0 , 1 (in L,R)
Only Mode Channel = 0 , 1 (in L,R)
Only Mode Channel = 0 ,1 (in L,R)
Frequency; Bank=0
Amplitude; Bank=1
Band Width; Bank=2
Filer 01, 02,..., 05
Filer 01, 02,..., 05
Filer 01, 02,..., 05
12, 13, 14, 15, 16
12, 13, 14, 15,16
12, 13, 14, 15, 16
0,..., 120
0,..., 60
0,..., 59
Only Mode Channel = 2, 3, 4, 5
Only Mode Channel = 2, 3, 4, 5
Only Mode Channel = 2, 3, 4, 5
Frequency; Bank=0
Amplitude; Bank=1
Band Width; Bank=2
Mute
23
0, 1
Output 1, 2, 3, 4
Mute OFF, ON
ModeCh=2, 3, 4, 5
Routing
24
0, 1
Connect Off/On InputL to Output1
Routing
25
0, 1
Connect Off/On InputL to Output2
Routing
26
0, 1
Connect Off/On InputL to Output3
Routing
27
0, 1
Connect Off/On InputL to Output4
Routing
28
0, 1
Connect Off/On InputR to Output1
Routing
29
0, 1
Connect Off/On InputR to Output2
Routing
30
0, 1
Connect Off/On InputR to Output3
Routing
31
0, 1
Connect Off/On InputR to Output4
Note:
Select the channel to edit by means of the controller 22 (Mode channel).
Warnings:
1. Before starting a MIDI session please set on the
LTO DRIVE2.3 the same MIDI channel used by the external
controller.
2. During a MIDI control session the unit's graphic display is NOT updated.
3. After MIDI use of
LTO DRIVE2.3 it's advisable to run a manual STORE to save preset changes done by means of
the external controller. After saving, reboot the
LTO DRIVE2.3 to use it as a stand-along unit.
4. When setting and resetting mutes (controller 23) by MIDI, the relative LEDs are NOT actived.
14
7
EMPTY
02
Name:
Num:
c. MIDI Setup
e. Password
With this function the user can decide if the device has to be protected from unauthorized tampering:
OUT EN.
OFF
01
CHANNEL
CHANNEL
OUT EN.
OFF
01
OUT EN.
OFF
01
CHANNEL
This page shows 4 output volumes and activity of the 4 output limiters. (see)
d. VU-Meter
Using Left and Right keys the user can move into the string, with the dial the blinking character can be edited, Enter
confirms the choice and Esc cancels operation allowing to maintain the old preset name. Upon confirmation the new
preset name will be shown in the lower left corner of the window and in the name field.
To get back to the main menu, select 1/1 and press the Esc key.
This function allows a simple MIDI configuration:
with the Up/Down key it's possible to select the MIDI channel and/or the output enable; selection is highlighted
printing the item in reverse color.
With the dial it is possible to change the value of the parameter, which will be operating immediately (no confirmation
needed). To get back to the main menu, select 1/1 and press the Esc key. These two parameters are system settings,
ie. They don't belong to a particular preset.
