Altera Arria 10 Avalon-ST Interface Скачать руководство пользователя страница 90

Страница: 90 / 147

Table 7-2: Altera

‑

Defined VSEC Capability Register, 0x200

The Altera

Defined Vendor Specific Extended Capability. This extended capability structure supports

Configuration via Protocol (CvP) programming and detailed internal error reporting.

Bits

Register Description

Value

Access

[15:0]

PCI Express Extended Capability ID. Altera-defined value for

VSEC Capability ID.

0x000B

[19:16]

Version. Altera-defined value for VSEC version.

0x1

[31:20]

Next Capability Offset. Starting address of the next Capability

Structure implemented, if any.

Variable

Table 7-3: Altera

‑

Defined Vendor Specific Header

You can specify these values when you instantiate the Hard IP. These registers are read

only at run

time.

Bits

Register Description

Value

Access

[15:0]

VSEC ID

. A user configurable VSEC ID.

User entered

[19:16]

VSEC Revision

. A user configurable VSEC revision.

Variable

[31:20]

VSEC Length

. Total length of this structure in bytes.

0x044

Table 7-4: Altera Marker Register

Bits

Register Description

Value

Access

[31:0]

Altera Marker

. This read only register is an additional marker. If

you use the standard Altera Programmer software to configure

the device with CvP, this marker provides a value that the

programming software reads to ensure that it is operating with

the correct VSEC.

A Device

Value

Table 7-5: JTAG Silicon ID Register

Bits

Register Description

Value

Access

[127:96]

JTAG Silicon ID DW3

Application

Specific

[95:64]

JTAG Silicon ID DW2

Application

Specific

[63:32]

JTAG Silicon ID DW1

Application

Specific

UG-01145_avmm_dma

2015.11.02

Altera-Defined VSEC Registers

7-9

Registers

Altera Corporation

Send Feedback

Содержание Arria 10 Avalon-ST Interface




















































































































































Результаты поиска

Содержание Arria 10 Avalon-ST Interface

Отзывы:

Похожие инструкции для Arria 10 Avalon-ST Interface

Бренды по названию

Популярные бренды

Altera Arria 10 Avalon-ST Interface, Руководство пользователя

Результаты поиска

Содержание Arria 10 Avalon-ST Interface

Отзывы:

Похожие инструкции для Arria 10 Avalon-ST Interface

Бренды по названию

Популярные бренды