Altera Arria 10 Avalon-ST Interface Скачать руководство пользователя страница 78

Страница: 78 / 147

Signal

Direction

Description

• 5’b11010: Speed.Recovery

• 5’b11011: Recovery.Equalization, Phase 0

• 5’b11100: Recovery.Equalization, Phase 1

• 5’b11101: Recovery.Equalization, Phase 2

• 5’b11110: Recovery.Equalization, Phase 3

• 5’b11111: Recovery.Equalization, Done

sim_pipe_pclk_in

Input

This clock is used for PIPE simulation only, and is derived from

the

refclk

. It is the PIPE interface clock used for PIPE mode

simulation.

sim_pipe_rate[1:0]

Input

Specifies the data rate. The 2-bit encodings have the following

meanings:
• 2’b00: Gen1 rate (2.5 Gbps)

• 2’b01: Gen2 rate (5.0 Gbps)

• 2’b1X: Gen3 rate (8.0 Gbps)

txblkst

For Gen3 operation, indicates the start of a block in the transmit

direction.

txcompl0

Output

Transmit compliance

<n>

. This signal forces the running

disparity to negative in compliance mode (negative COM

character).

txdata0[31:0]

Output

Transmit data. This bus transmits data on lane

<n>

txdatak0[3:0]

Output

Transmit data control

<n>

. This signal serves as the control bit

for

txdata

<n>

. Bit 0 corresponds to the lowest-order byte of

rxdata

, and so on. A value of 0 indicates a data byte. A value of 1

indicates a control byte. For Gen1 and Gen2 only.

txdataskip0

Output

For Gen3 operation. Allows the MAC to instruct the TX interface

to ignore the TX data interface for one clock cycle. The following

encodings are defined:
• 1’b0: TX data is invalid

• 1’b1: TX data is valid

txdeemph0

Output

Transmit de-emphasis selection. The value for this signal is set

based on the indication received from the other end of the link

during the Training Sequences (TS). You do not need to change

this value.

txdetectrx0

Output

Transmit detect receive

<n>

. This signal tells the PHY layer to

start a receive detection operation or to begin loopback.

UG-01145_avmm_dma

2015.11.02

PIPE Interface Signals

6-25

IP Core Interfaces

Altera Corporation

Send Feedback

Содержание Arria 10 Avalon-ST Interface




















































































































































Результаты поиска

Содержание Arria 10 Avalon-ST Interface

Отзывы:

Похожие инструкции для Arria 10 Avalon-ST Interface

Бренды по названию

Популярные бренды

Altera Arria 10 Avalon-ST Interface, Руководство пользователя

Результаты поиска

Содержание Arria 10 Avalon-ST Interface

Отзывы:

Похожие инструкции для Arria 10 Avalon-ST Interface

Бренды по названию

Популярные бренды