background image

Press the 

DOWN or UP

 button to lower or raise the shade. Press the 

STOP/FAVORITE

 to stop the shade 

at the desired position.

Touch & Go Feature:

To fully raise or lower the shade, simply press the 

UP or DOWN

 button and then release. The shade will 

automatically stop when it reaches the upper or lower limit. (If the upper or lower limits are not set at the 
desired positions, see the Adjust Motor Limits section)

Note: 

Upper and lower limits stops are set at the factory. An intermediate or “favorite” position is not set at 

the factory. See “Setting a Favorite Position” section for more information.

The upper and lower limits have been set at the factory. If you need to make adjustments to the limits, follow the instructions below. 
Press the 

SETTING

 button on the back of the wand and hold it in until the motor stops beeping. 

This will clear both the upper and lower factory limits as well as a favorite if one was set.
Set Upper Limit - Press the 

UP

 button to get the shade close to the desired upper limit and then 

press the 

STOP

 button to stop the shade. Tap the 

UP or DOWN

 button to move the shade to the 

desired position. To save the location, press the 

SETTING

 button until the motor beeps.

Set Lower Limit - Press the 

DOWN

 button to get the shade close to the desired lower limit and 

then press the 

STOP

 button to stop the shade. Tap the 

UP or DOWN

 button to move the shade 

to the desired position. To save the location, press the 

SETTING

 button until the motor beeps.

Setting and Using a Favorite Position

Use the 

UP or DOWN

 buttons to position the shade at the desired “favorite” position. First press 

and hold the 

SETTING

 button on the back of the wand. While holding the 

SETTING

 button press 

and hold the 

UP

 button. Release both buttons when the shade beeps.

With the shade at either the upper or lower limit, simply press the 

STOP/FAVORITE

 button to  

bring the shade to the “favorite” position. To go to the “favorite” position from any other location, 
make sure the shade has been stopped for at least three seconds before pressing the 

STOP/ 

FAVORITE

 button.

Changing a Favorite Position

Use the 

UP or DOWN

 buttons to position the shade at the desired “favorite” position. 

First press and hold the 

SETTING

 button on the back of the wand. While holding the 

SETTING

 

button press and hold the 

UP

 button. Release both buttons when the shade beeps.

This establishes a new “favorite” position and erases the old.

5

When the shade begins to operate slower than normal or only beeps when you attempt to operate, it is time to charge the battery.

•  Plug the 8.4v charger into the port on the wand.
•  Plug the charger into an electrical outlet.
•  A red light on the charger indicates that the battery is charging.
•  To fully charge the batteries, allow the batteries to charge for at least 1 hour after the  

light on the charger turns green. A typical charge cycle can take between 4-6 hours. 

UP

Stop/Favorite

Down

UP

Stop

Down

Setting 

Button

UP

Stop/Favorite

Down

Setting 

Button

Charging Port

Operating the Shade

Adjust Motor Limits (if desired)

Setting a Favorite Position

Charging the Motor Battery

Содержание HONEYCOMB SHADES













Отзывы: