background image

2

-EN

ALPINE HCE-C200R  68-09359Z09-A (EN)

 WARNING

 

 WARNING

This symbol means important instructions.
Failure to heed them can result in serious
injury or death.

WHEN REVERSING THE CAR, CHECKING BEHIND AND
AROUND THE CAR MUST BE DONE VISUALLY BY THE
DRIVER.

The TOPVIEW

 

FRONT/REAR CAMERA assists the driver in

checking behind and around by sending images to the screen
showing conditions behind and around the car. The camera uses a
wide-angle lens, therefore, there is a difference in distance
perspective between what is normally seen and what appears on
the screen. Also, the images shown by the rear camera are
reversed, so as to appear the same as what is seen through the
rearview mirror.

DO NOT DISASSEMBLE OR ALTER.

Doing so may result in an accident, fire or electric shock.

KEEP SMALL OBJECTS SUCH AS BOLTS OR SCREWS OUT
OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury. If swallowed,
consult a physician immediately.

USE THE CORRECT AMPERE RATING WHEN REPLACING
FUSES.

Failure to do so may result in fire or electric shock.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE
NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due to
electrical shorts.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying capacity of
the wire and result in fire or electric shock.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER
VEHICLE OPERATION, SUCH AS THE STEERING WHEEL
OR SHIFT LEVER.

Doing so may obstruct forward vision or hamper movement etc.
and results in serious accident.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.

When drilling holes in the chassis for installation, take
precautions so as not to contact, damage or obstruct pipes, fuel
lines, tanks or electrical wiring. Failure to take such precautions
may result in fire.

Operating Instructions

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR
STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any other
safety-related system), or tanks should NEVER be used for
installations or ground connections. Using such parts could
disable control of the vehicle and cause fire etc.

MINIMIZE DISPLAY VIEWING WHILE DRIVING.

Viewing the display may distract the driver from looking ahead of
the vehicle and cause an accident.

DO NOT ALLOW CABLES TO BECOME ENTANGLED IN
SURROUNDING OBJECTS.

Arrange wiring and cables in compliance with the manual to
prevent obstructions when driving. Cables or wiring that obstruct
or hang up on places such as the steering wheel, shift lever, brake
pedals, etc. can be extremely hazardous.

USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.

Use for other than its designed application may result in fire,
electric shock or other injury.

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or
product damage.

CHECK THAT THE CAMERA MOUNTING IS ATTACHED
SECURELY, AND THAT THE SCREWS ARE TIGHT BEFORE
DRIVING.

Failure to do so may result in an accident.

WHEN INSTALLING THE CAMERA, OR WHEN CHECKING
IT IS INSTALLED SECURELY, DO SO AFTER PARKING THE
CAR IN A LEVEL, SAFE PLACE, TURNING OFF THE
ENGINE, AND APPLYING THE HAND BRAKE.

Failure to do so may result in an accident.

WHEN USING A DRILL TO MAKE A HOLE, TAKE
PRECAUTIONS SUCH AS WEARING GOGGLES SO
FRAGMENTS DO NOT GET INTO THE EYES.

Failure to do so may result in injury.

Содержание HCE-C200F


















Отзывы: