58
-EN
To prevent external noise from entering the audio system.
•
Locate the unit and route the leads at least 10 cm away from the car harness.
•
Keep the battery power leads as far away from other leads as possible.
•
Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
•
If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
•
Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
1
Antenna Receptacle
2
Audio Interrupt In Lead (Pink/Black)
Connect this lead to the Audio Interface output of a cellular
phone which provides ground shorting when a call is
received.
3
Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
4
Dimmer Lead (Orange)
This lead may be connected to the vehicle’s instrument
cluster illumination lead. This will enable the vehicle’s
dimmer control to dim the backlighting of the unit.
5
Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle’s fuse
box or another unused power source which provides (+) 12V
only when the ignition is turned on or in the accessory
position.
6
Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
7
Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
•
This lead should be used only for controlling the vehicle's
power antenna. Do not use this lead to turn on an amplifier or
a signal processor, etc.
8
Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle’s
battery.
9
ISO Power Supply Connector
!
ISO Connector (Speaker Output)
"
Left Rear (+) Speaker Output Lead (Green)
#
Left Rear (–) Speaker Output Lead (Green/Black)
$
Left Front (+) Speaker Output Lead (White)
%
Left Front (–) Speaker Output Lead (White/Black)
&
Right Front (–) Speaker Output Lead (Grey/Black)
(
Right Front (+) Speaker Output Lead (Grey)
)
Right Rear (–) Speaker Output Lead (Violet/Black)
~
Right Rear (+) Speaker Output Lead (Violet)
+
Remote Control Input Lead (White/Brown)
Connect the external Alpine product to the remote control
output lead.
,
Monitor Control Lead (White/Pink)
Connect this to the Monitor Control Lead of the touch panel-
compatible monitor.
-
Video Output Connector
This connector is used in combination with the video inputs
of another video product (Touch panel compatible monitor,
etc.)
.
External Junction Box Connector
Connect to the external junction Box (included)
/
External Junction Box
Use when connecting optical digital cable or the remote
control interface box.
Connect to the external junction box connector.
•
Do not install the external junction box at a location subjected
to water such as under the floor mat or air conditioner. This
may cause a malfunction.
•
Do not bundle the external junction box cable with other audio cables.
Doing so may induce noise into your system.
•
Keep the external junction box away from the Antenna cables
and the rear side of the unit, otherwise noise may be generated
when receiving radio broadcast.
:
Digital Output Terminal (Optical)
Use when combining optical digital input compatible
products.
;
Steering Remote Control Interface Connector
To steering remote control interface box.
•
Use a steering remote control extension cable (included) if
necessary.
<
Vehicle Display Interface Connector
Vehicle Display Interface control signals.
Connect this to the optional Vehicle Display Interface box.
•
For details about connections, consult your nearest ALPINE
dealer.
=
Ai-NET Connector
Connect this to the output or input connector of other product (CD
changer, Equalizer, iPod adapter
*
,
etc.) equipped with Ai-NET.
* When connecting iPod, the adapter KCA-420i is required. For
details about connections, refer to the manual of KCA-420i.
>
Fuse Holder (10A)
?
Rear Output RCA Connectors
RED is right and WHITE is left.
@
Front Output RCA Connectors
RED is right and WHITE is left.
[
Subwoofer Output RCA Connectors
RED is right and WHITE is left.
\
Power Supply Connector
]
System Switch
When connecting a processor using Ai-NET, place this
switch in the EQ/DIV position. When no device is
connected, leave the switch in the NORM position.
•
Be sure to turn the power off to the unit before changing the
switch position.
^
Ai-NET Cable (Included with CD Changer)
_
RCA Extension Cable (sold separately)
{
ISO/JASO Antenna Adapter (sold separately)
ISO/JASO Antenna Adaptor may be required, depending on
the vehicle.
Содержание DVA-9860R
Страница 64: ......
