Alpine CDA-7998R, Руководство пользователя

Страница: 53 / 56

51
-EN
1
Antenna Receptacle
Connect to the supplied ISO antenna convertor plug.
2
Audio Interrupt In Lead (Pink/Black)
Connect this lead to the Audio Interface output of a cellular
phone which provides ground shorting when a call is
received.
3
Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
4
Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle’s fuse
box or another unused power source which provides (+) 12V
only when the ignition is turned on or in the accessory
position.
5
Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
NOTE
This lead should be used only for controlling the vehicle's power
antenna. Do not use this lead to turn on an amplifier or a signal
processor, etc.
6
Choke Coil with Fuse Holder (7.5A)
7
Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle's
battery.
8
ISO Power Supply Connector
9
Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
!
Power Supply Connector
"
Ai-NET Connector
Connect this to the output or input connector of other
product (CD changer, Equalizer, etc.) equipped with Ai-
NET.
#
DC/DC Converter
NOTES
•
Do not install the converter at a location subjected to water
such as under the floor mat or air conditioner. This may cause
a malfunction.
•
Do not bundle the DC/DC converter cable with other audio
cables. Doing so may induce noise into your system.
•
Keep the DC/DC converter away from the Antenna cables and
the rear side of the unit, otherwise noise may be generated
when receiving radio broadcast.
$
Ai-NET Cable (Included with CD Changer)
%
Front Output RCA Connectors
RED is right and WHITE is left.
&
Rear Output RCA Connectors
RED is right and WHITE is left.
(
Subwoofer Output RCA Connectors
RED is right and WHITE is left.
)
RCA Extension cable (Sold Separately)
~
Remote Control Interface Connector
To remote control interface box.
+
System Switch
When connecting a processor using Ai-NET, place this
switch in the EQ/DIV position. When no device is
connected, leave the switch in the NORM position.
NOTE
Be sure to turn the power off to the unit before changing the
switch position.
,
Setting the 3WAY/2 WAY switch
Set the 3way/2way Switch according to your audio system.
-
Digital Output Connector
Connect this to any other optical digital products of ALPINE.
The digital signal will be output when the CD mode is on.
The system whose frequency range is divided between
the high frequency range and the low frequency range. The system whose frequency range is divided among
the high frequency range, mid frequency range, and
the low frequency range.
The position of switching the switch: F/R/Sub-W
Front high range
speaker (L)
Rear high range
speaker (L)
Front high range
speaker (R)
Rear high range
speaker (R)
Low range
speaker (L) Low range speaker
(R)
The position of switching the switch: 3WAY
High range
speaker (L)
Mid range
speaker (L)
High range
speaker (R)
Mid range speaker
(R)
Low range
speaker (L) Low range speaker
(R)
NOTES
•
Use the SUB-W output to connect the unit to the Low Range speaker.
•
You cannot adjust the FADER when setting to 3 WAY.
Output of this unit :
Front output Rear output SUB-W output
CDA-7998R
Amplifiers
RCA Connectors
CDA-7998R
Amplifiers
RCA Connectors