34
-EN
Adjusting the Frequency
Touch
[ ]
or
[ ]
of “Frequency” to adjust the frequency of the
selected band.
Adjustable frequency bands:
20 Hz to 20 kHz (in 1/3 octave steps)
Adjusting the Level
Touch
[
]
or
[
]
of “Level” to adjust the level of selected band.
Setting contents:
-14 to +14 (Initial setting: 0)
Setting the Bandwidth
Touch
[ ]
or
[ ]
of “Q Factor” to select the bandwidth.
Setting contents:
Wide (Initial setting) / Medium / Narrow
2
To adjust another band, repeat step 1, and adjust all
bands.
3
To store the adjusted setting value, touch and hold
[Preset 1]
,
[Preset 2]
, or
[Preset 3]
for at least 2 seconds.
• Band2 and Band8 are the same as the Bass and Treble controls.
• For details on setting Bass and Treble, see “Adjusting Bass Level/Treble
Level” (page 19).
• Settings exceeding the frequency of adjacent bands are not available.
• While adjusting the Dual HD EQ, you should consider the frequency
response of the connected speakers.
• When the Dual HD EQ is adjusted, the Equalizer Presets are
overridden.
• When Equalizer Presets is set, the linked Dual HD EQ settings are also
changed. We recommend storing Dual HD EQ settings in a Preset in
advance.
• Touch
[Flat]
to initialize all values.
Calling the Dual HD EQ adjusted value
Calling the pre-set Dual HD EQ adjusted value.
Touch
[Preset 1]
,
[Preset 2]
, or
[Preset 3]
on the Dual HD EQ
screen.
The setting stored in the Preset will be recalled.
Before performing the following procedures, see “About the Crossover”
(page 36).
Setting item:
X-Over
• When the Sound Setup of the Shortcut Setup is selected to “BASS
ENGINE SQ,” you cannot perform the set up.
1
Touch
[Channel]
to select the channel.
Each time you touch, the channel switches.
• The channel being adjusted is displayed in red.
2
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch
[ ]
or
[ ]
of “Frequency,” and then select the cut-off
frequency.
Setting contents:
20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) / 100 / 125 / 160 / 200 Hz
Adjusting the Slope
Touch
[ ]
or
[ ]
of “Slope,” and then adjust the HPF or LPF slope.
Setting contents:
0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct.
Adjusting the Level
Touch
[
]
or
[
]
of “Level,” and then adjust the HPF or LPF level.
Setting contents:
-12 to 0 dB (Initial setting: 0)
3
Repeat steps 1 to 2 to make adjustment to the other
channels.
4
To store the adjusted setting value, touch and hold
[Preset 1]
,
[Preset 2]
, or
[Preset 3]
for at least 2 seconds.
• Touch
[Flat]
to initialize all values.
• If the Rear Speaker setting is “Off,” the Rear Speaker setting cannot be
edited (page 32).
• If the Subwoofer setting is “Off,” the Subwoofer setting cannot be edited
(page 32).
• While adjusting the X-Over you should consider the frequency response
of the connected speakers.
Calling the X-Over adjusted value
Calling the pre-set X-Over adjusted value.
Touch
[Preset 1]
,
[Preset 2]
, or
[Preset 3]
on the X-Over
screen.
The setting stored in the Preset will be recalled.
Band1:
20 Hz~100 Hz (63 Hz)
Band2:
63 Hz~315 Hz (125 Hz)
Band3:
125 Hz~500 Hz (250 Hz)
Band4:
250 Hz~1 kHz (500 Hz)
Band5:
500 Hz~2 kHz (1 kHz)
Band6:
1 kHz~4 kHz (2 kHz)
Band7:
2 kHz~7.2 kHz (4 kHz)
Band8:
5.8 kHz~12 kHz (8 kHz)
Band9:
9 kHz~20 kHz (16 kHz)
Adjusting the Crossover Settings (X-Over)
Front HPF
Rear HPF
Subw. LPF
Front HPF
Содержание 9ZUA147
Страница 2: ......
Страница 103: ...103 EN List of Language Codes For details see page 69...
Страница 111: ......
