manualshive.com logo in svg

Alpha Professional Tools Ecocutter ECC-125, Инструкция по эксплуатации

Поделиться
Скачать
Alpha Professional Tools Ecocutter ECC-125 Скачать руководство пользователя страница 10

10

4.  Inspect the saw blade.

–  Check if you have a specified blade.

–  Never use cracked, chipped, or any damaged blades.

–  Follow the procedures specified in the instruction manual to properly attach 

applicable accessories.

5.  Check the power outlet.

–  When the plug of the power supply cord is easily pulled out of the power outlet, 

the outlet should be replaced.  For such tasks, consult an electrician.  If the power 

outlet is used on a continuous basis, it may overheat and cause accidents. 

6.  Perform test runs.

  

WARNING!

1.  Before turning the switch ON, make sure the rotating parts are not touching    

anything. If the switch is turned ON while they are in contact with anything  

 

else, the blade may get damaged and it may cause injuries.

2.  When a new blade is attached and the switch is turned ON, keep your body  

 

well away from the exposed sides of the tool for a moment until the machine    

reaches its full speed.

3.  It is very dangerous to perform cutting operations using cracked, chipped or damaged 

blades. Before starting cutting operations, keep the tool away from anyone nearby. Be 

sure to perform a few test runs to check whether there are any abnormalities.

  ABOUT DOUBLE INSULATION

This machine is designed with double insulation. Two insulations are used between the 

conductor and the outer body of the machine.  An Electric Machine with the double insulation 

highly improves safety from electric shocks.  Do not attach or replace unspecified parts and 

do not assemble incorrectly. This may cause the  insulation to malfunction.   

   LAWS AND REGULATIONS OF NOISE LEVELS

Please observe local laws and regulations regarding noise level in order to avoid disturbing 

surrounding areas.  Install a soundproof wall if required to comply with the local laws and 

regulations. 

Содержание Ecocutter ECC-125





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды