Alpha Moisture Systems DS1200-PDT Скачать руководство пользователя

Страница: 16 / 17

Model DS1200-PDT - Dewpoint Hygrometer

Output Signal

: 4 to 20mA Linear to its range.

Operating Voltage

: 10V - 30V DC.

Factory calibration

: Supplied with Certiﬁcate of Calibration traceable to NPL/NIST

Accuracy

: ± 2°C dewpoint (NPL / NIST traceable)

Temperature compensation : Temperature compensated for operating range.

Operating temperature

: -30…70°C (ideal 0…50°C)

Storage Temperature

: -40…80°C

Operating Pressure

: From 1kPa (0.01 barA) to Maximum 5,000kPa (50 barA)

Sample Flow Rate

: Independent but ideally 2 to 3 litres per minute.

Max: 25 litres/min.

Connection

: M12, 5-pole

EMC

: DIN EN 61326

Transmitter Enclosure

: Zinc alloy, PC, ABS

Sensor Protection

: 316 Sintered stainless steel ﬁlter - 50 micron

Weatherproof Classiﬁcation : IP65/NEMA4 when Connector mated to Transmitter.

Mechanical Connection

: G 1/2”

Mechanical Warranty

: 12 months in case of faulty workmanship and defective parts.

Speciﬁcations PDT Transmitter

Speciﬁcations PDT Transmitter Holder

High Grade 316 Stainless Steel - Part Number SH-PDT

Содержание DS1200-PDT


















Результаты поиска

Содержание DS1200-PDT

Отзывы:

Похожие инструкции для DS1200-PDT

Бренды по названию

Популярные бренды

Alpha Moisture Systems DS1200-PDT, Руководство пользователя

Результаты поиска

Содержание DS1200-PDT

Отзывы:

Похожие инструкции для DS1200-PDT

Бренды по названию

Популярные бренды