background image

6

Model DS1200-PDT - Dewpoint Hygrometer

Safety Information

The 

DS1200-PDT

has been designed to be connected to hazardous electric voltages and

must be protected by a 

5amp

fused plug to the mains/AC supply. 

Check to establish that all wiring and connections are not damaged. If damage is 

observed to any electrical wiring, connections or damage to the apparatus they 

must not

be connected to the mains/AC supply but returned to your local distributor for rectification. 

Warnings

Risk of electric shock - Do not open any part of the enclosures of the 

Model DS1200-PDT

whilst connected to the mains/AC supply.

Do not connect the 

Model DS1200-PDT

to the mains/AC supply until all other connections

and pipework is secure and have been tested.

Ignoring this safety information could result in severe personal injury and/or mechanical

damage to the 

Model DS1200-PDT.

The product specifications must not be exceeded at anytime, as this may cause personal 

injury, damage to the instrument and sensor or cause risk of fire. 

Do not connect the 

Model DS1200-PDT

to any other device that is not recommended in

this manual.

Ensure that the 

Model DS1200-PDT

does not come into direct contact with water or any

other liquids. See IP/NEMA protection in the product specifications.

To avoid the risk of electric shock, risk of damage or fire, these safety instructions and

guidelines must be followed. Only qualified personnel/technicians should install these 

units to the mains/AC supply and connecting pipework to ensure it is completely safe by

testing and recording before use. 

It is the responsibility of the customer to ensure safe working conditions especially working

with hazardous gases and liquids. Leak tests should be carried out periodically by qualified

personnel.

Safe Isolation

Switch off at the mains/AC socket and remove the plugs before any maintenance is carried

out by a qualified person. Always test components with an approved voltage meter before

handling to ensure it is completely dead.

YOU MUST ALSO READ THE WARNING INFORMATION ON PAGE 10.

Содержание DS1200-PDT


















Отзывы: