Alpha Moisture Systems DS1200-PDT Скачать руководство пользователя

Страница: 10 / 17

Model DS1200-PDT - Dewpoint Hygrometer

M12 connector plug

If no connection cable is ordered, the sensor will be supplied with a M12 connector plug.

The user can connect the supply and signal cables as indicated in the connection diagram

below.

PDT Connections:

Pin 2 to Pin 45 on

DS1200

Pin 3 to Pin 46 on

DS1200

Installing the Model PDT in a Air/Gas Sampling System

Warning: Do not exceed a pressure of 50 bar.

Observe the operating ranges of the sensor. The probes are damaged if they are

overheated.
Observe maximum storage and transport temperature as well as maximum

operating temperature (i.e. protect the instrument from direct sunlight).

Important:

Before installation, bleed compressed air systems in order to remove

condensate and particles to avoid contamination.

Содержание DS1200-PDT


















Результаты поиска

Содержание DS1200-PDT

Отзывы:

Похожие инструкции для DS1200-PDT

Бренды по названию

Популярные бренды

Alpha Moisture Systems DS1200-PDT, Руководство пользователя

Результаты поиска

Содержание DS1200-PDT

Отзывы:

Похожие инструкции для DS1200-PDT

Бренды по названию

Популярные бренды