background image

14

Subject to change without notice  |  83031300dUK  |  ait-deutschland GmbH

14  Installation of the control unit

Situated at different heights in the upper facade of the 

operating side of the unit are recesses (each with 4 re-

cesses) for the fastening of the control unit:

1 four upper recesses

2 four lower recesses

4 hooks are located on the back side of the control unit 

and can be used to hang the control unit on the front 

facade of the unit:

1.  Hang the control unit’s hooks on the recesses of 

the upper facade (either in the upper or lower re-

cesses.

Example:  Control unit in upper recesses

2.  Push the control unit down until it locks into posi-

tion.

3.  Stick the heating and heat pump regulator’s con-

trol cable into the 

right

 bushing on the bottom of 

the control unit.

 NOTE

A connection to a computer or a network can 

be installed via the left bushing on the bottom 

of the control unit, thus allowing the heating 

and heat pump regulator to be controlled re-

motely. One pre-condition is that a screened 

network cable (category 6) be installed 

through the unit when installing the unit.

  Operating manual for the heating and heat pump 

regulator, part 2, “Web server” section

If this network cable is available, insert the 

network cable’s RJ-45 plug into the left bush-

ing of the control unit.

 NOTE

The network cable can be exchanged at any 

time. In order to be able to connect it, the 

screen must first be removed.

Содержание 10078702





































Отзывы: