Allora Positive Contact PCS-250 Скачать руководство пользователя страница 12

Positive Contact Control Units conform with the EEC directive EMC 89/336/EEC as 
amended by 92/31/EEC and 93/68/EEC.

In compliance with the directive, the EC Declaration of Conformity and related 
Technical Documentation is maintained at the following address for inspection by 
the appropriate officials:

Allora International, LLC

1825 Dolphin Dr.  Unit B

Waukesha, WI  53186

PCS-250              rev.121010

Positive Contact – Hazardous Materials

All 

Positive Contact

products and packaging are manufactured with RoHS compliant materials.  They are free of 

Bromide Halogens (PBB, PBDE), Mercury, Cadmium, and Chrome 6+.
All 

Positive Contact 

products are Lead Free.

All 

Positive Contact

products comply with current EU environmental standards, including directive amendments 

regarding the use of perfluorooctane sulfonates, (PFOS).
All 

Positive Contact 

products and packaging are free of any material containing Asbestos.

All 

Positive Contac

t foam packaging is free of CFC’s, HCFC’s or HFC’s.  The foam and its ash is non-toxic, landfill 

safe and recyclable.

RoHS Compliant

Allora International, LLC

1825 Dolphin Drive 

Unit B 

Waukesha, WI 53186

Phone

+1.262.246.6800 

Fax

+1.262.246.6866 

Website

www.alloraintl.com 

E-Mail

[email protected]

Содержание Positive Contact PCS-250













Отзывы: